It is currently Sun Aug 25, 2019 7:37 am

All times are UTC - 8 hours

Post new topic Reply to topic  [ 2 posts ] 
Author Message
 Post subject: Antec 1200 - 11x Suspended HDD Project
PostPosted: Thu May 01, 2014 3:36 pm 
Patron of SPCR

Joined: Wed Dec 15, 2004 12:00 pm
Posts: 3307
Location: Essex, England
I have an Antec 1200 case and I want to suspend 11 HDD's, all 3.5".

I have had a look through the various threads about suspension and what people have used. If you look at the inside of my case and the mounting options for elastic bands on cords, you will see from the images in the following link that thick cord is not possible without drilling holes - so bands would be better. ... ed/?page=6

The only HDD suspension that I have ever done was some years ago with "StretchMagic" 1mm cord with a PATA laptop HDD, a very different proposition from my next project.

Here is the real question, what type of elastic band would you suggest, none of the bands that I look at on the internet say how much weight the band will hold, and how much they will stretch with X weight.

Is 1/4 inch (x2 bands per drive) enough.? Is there a particular brand to use.?

As far as knotting or tying is concerned, I am sure I can figure that out at the time. One thing I will be doing for sure is securing the drives so they cannot slip out front to back when I need to move the case.


Main PC, P180, CM Silent Pro 500M, i5 3570k @ 4.2Ghz, 8-GB @ 2,400MHz, 512GB 850 EVO, 500 Extreme II, 2x 2.5" drives, MSI 660Ti Twin Frozr.
Server, under reconstruction, 380W Enermax Pro82+, positive pressure only.

 Post subject: Re: Antec 1200 - 11x Suspended HDD Project
PostPosted: Fri Jul 11, 2014 1:05 am 

Joined: Fri Jul 11, 2014 12:46 am
Posts: 7
I have an Antec 1200 and afaik it can only receive intake airflow by the HDD drive cages. So im interested to know why that isnt an issue. If you are suspending the drives, making sure they are receiving cooling is important imo.

I havent suspended drives in the 1200 so no experience there sorry.

Looking at the case though, the 2 rectangle slits on each side of the drive bays could be used for threading the elastic cord. I dont think you need extra heavy duty elastic (and you could always just double up with a thinner elastic). The drives suspension mounted in an Antec 1200 should each have their own separate elastic - you dont need to hang more than one drive off a piece of elastic, so accumulated weight of the drives is not an issue.

I would just use an elastic cord thatll fit through the drive screw holes. That would give you the option of threading through the recantagular slits or the round holes.

Ideally youd also want a hole in the middle of the drive bay to secure drives with elastic in the middle too. But, despite the lack of a middle hole, you could instead horizontally cross the elastic from back to front across the top and bottom of the drive, and this would also help to secure it in the middle.

But of course, if you dont need the drives to be high performance 7200rpm ones, then just go for a lower rpm version. Lower rpm should mean lower vibration. Also heavier drives (higher capacity usually) will vibrate more than others.

Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 2 posts ] 

All times are UTC - 8 hours

Who is online

Users browsing this forum: No registered users and 2 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group