mini p180 + HDD box + undervolted fans

Show off your quiet rig.

Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Lawrence Lee

Chaendler
Posts: 53
Joined: Tue Aug 16, 2005 5:58 am
Location: Spain

Post by Chaendler » Wed Nov 05, 2008 3:59 pm

Sorry, pianomambo.

Can you tell us what did you use to block the top hole (after removing the 200mm fan).

It's like a piece of metal, but I can't tell.

Also, have you tried the possibility of flipping the PSU fan so it acts as an intake fan? (maybe is a silly idea, I'm just wondering if you have tried it).


thanks
Case: Antec P180 Mini fully isolated with Acoustipack.
Disk: Velociraptor in Scythe Quite Drive on foam.
CPU: E8500 + HR-01 (passive).
VGA: 9800gt + Accelero S1 (passive).
PSU: Silverstone ST60F PSU modded + Noctua.
Motherboard: Asus P5Q-EM (passive).
Case Fan: 3 Noctua NFP-12 + T-Balancer.

pianomambo
Posts: 11
Joined: Mon Jul 07, 2008 11:31 am
Location: France

Post by pianomambo » Wed Nov 19, 2008 12:33 pm

Hi everybody !

About the 200mm fan : it is clearly noisier than the Noctua. Second problem : it can't work at very low speed (too heavy, too high hysteresis). Third problem, the place : on the top of the case, it is in direct way to my ears. The best places for fans are inside the case (as i did), on the back, or behind the front door.

I replace the 200mm fan with a simple peace of metal (not so easy : it was stuck. If you want to remove it, be careful !).

About the possibility of flipping the PSU fan as an intake fan : The Power Supply is the second hot spot of my computer (after the CPU). I did several tests on the subject (see my pic on page 1 with the four cases). My conclusions on the PSU were :
- no intake fan for PSU (never),
- and separate air flow between PSU and CPU (not in serial).

Best regards

JackyPerformance.com
Posts: 67
Joined: Sun Sep 02, 2007 3:30 am
Location: www.NEQX.com
Contact:

Post by JackyPerformance.com » Mon May 18, 2009 4:16 am

pianomambo,
how is that Antec mini p180 holding up after all this time? Have you made any changes to it yet?

SebRad
Patron of SPCR
Posts: 1121
Joined: Sun Nov 09, 2003 7:18 am
Location: UK

Post by SebRad » Mon May 18, 2009 8:52 am

Hi, part of the reason you can't measure the very slow fan speeds is the Noctua fans themselves. I've used 120mm and 80mm Noctua's and they don't seam to put out any speed signal below about 6V. It seams to me some fans can read at very low speed and others can't
Also often have to configure SpeedFan to get the low rpm readings.
SpeedFan -> Configure -> Advanced -> Winbond xxxx (or whatever the monitoring chip on your board is) -> FanX divisor. Choice of powers of 2 for setting, I find it defaults to 4-8 and need at least 32 for low fan speeds, tick the "remember it" box too.
I've just been experimenting with a Xilence 1500rpm 80mm fan and can read it's speed down to 285rpm at 30%, 25% and it stops altogether.
Regards, Seb
i7 2600k under NH-C14 w/2xTY-147PWM fans, P8P67Deluxe, 8GB RAM, GTX560Ti OC w/TwinTurbo II and BIOS fanspeed mod. MX100 512GB & 2TB EARX in Scythe QuietDrive outside case. Antec Signature 650 fan swapped. CoolerMaster 201C with 2x92 + lower 92mm fan out rear, holes-in-floor and mesh top+front intakes.

pianomambo
Posts: 11
Joined: Mon Jul 07, 2008 11:31 am
Location: France

Post by pianomambo » Sat May 23, 2009 4:45 pm

SebRad --> Thanks for very interesting contribution.

JackyPerformance --> To answer your question, i haven't made any change. It works perfectly.

I open it sometimes, just to check if the fans are running (I cant hear them).

Since last year, I have forgotten that computers produce noise.

Best regards...

pianomambo
Posts: 11
Joined: Mon Jul 07, 2008 11:31 am
Location: France

Post by pianomambo » Tue Jun 16, 2009 12:01 pm

Hi Everybody,

I would like to build a other computer, with different features (a integrated server).

Do you know how much can I sell this one ? (and how ?)

Thank you very much for your help !

Best regards,

PM

ps : If someone is interested, he can join me here :
pianomambo (at) gmail.com

rei
Posts: 967
Joined: Wed Dec 08, 2004 11:36 am

Post by rei » Wed Jun 17, 2009 7:23 am

It's a pity you're in France--shipping that thing over the ocean to North America is expensive and risky.

I hope you can sell it to a euro SPCR member.

pianomambo
Posts: 11
Joined: Mon Jul 07, 2008 11:31 am
Location: France

Post by pianomambo » Wed Jun 17, 2009 8:01 am

Hum... I finally keep it. And I build a server aside.
The fantastic "Lian-Li modular cube case" will be for a other time.

Best regards !

PM

Post Reply