Cutting a hole in a case
Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Devonavar
Cutting a hole in a case
Okay, if I wanna punch a hole in the side of my case to fit in a duct right over the CPU, what's the best way to do that? (If you need specifics: Its an SLK 3700...)
Also, I'm making a PSU duct with the hole at the top (SEE ARM's PSU duct), any thoughts/ideas on how to do this?
Thanks.
Also, I'm making a PSU duct with the hole at the top (SEE ARM's PSU duct), any thoughts/ideas on how to do this?
Thanks.
Measure well, drill a hole close to the center, and cut the hole in a spiral outwards with a good pair of tin snips.
See this thread for good tips.
See this thread for good tips.
Dremel works, but it's really, really, REALLY slow for holes of some size. Hole saw should be the best -- if you have one of exactly the size you want -- but hole saws for metal are pretty expensive, and you need a fairly high-powered machine tool for it. If you already have the tool and the hole saw, go for it, but a good pair of tin snips do the job just as well.
here's a way make a hole
if u can fasten the side panel to a piece of wood and use a regular drill with a hole saw.. it will go through metal.. though i dun use this method.
What i do is i use a marker to draw an outline of the hole i wanna make. then i use a drill to drill holes, very close to each other, following the outline of the pattern. Then u can either snip between the holes, use a coping saw, hacksaw, or dremel to cut it out (basically, like connect the dots). its best to use a bit that creates its own pilot hole so holes are precise.. or even better, use a drill press machine. Afterwards use a metal file to sand down the rough jaggy edges. Then use finer grades of sandpaper to get it very smooth and round out the metal so it wont cut u. You can get the holes to look as good as if the case was manufactured that way. I think a thick flange would also help reduce noise. =) and I've seen too many bad cutouts and hole-ing on this forum. My holes follow the outline of the fan cavity, but I wonder if round holes would decrease noise even if it doesn't allow for as much passage of air.. I will know once i get some silicone to seal the fan/isolate the fan from the case. oh, wear proper protection.. maybe even a breathing mask.
What i do is i use a marker to draw an outline of the hole i wanna make. then i use a drill to drill holes, very close to each other, following the outline of the pattern. Then u can either snip between the holes, use a coping saw, hacksaw, or dremel to cut it out (basically, like connect the dots). its best to use a bit that creates its own pilot hole so holes are precise.. or even better, use a drill press machine. Afterwards use a metal file to sand down the rough jaggy edges. Then use finer grades of sandpaper to get it very smooth and round out the metal so it wont cut u. You can get the holes to look as good as if the case was manufactured that way. I think a thick flange would also help reduce noise. =) and I've seen too many bad cutouts and hole-ing on this forum. My holes follow the outline of the fan cavity, but I wonder if round holes would decrease noise even if it doesn't allow for as much passage of air.. I will know once i get some silicone to seal the fan/isolate the fan from the case. oh, wear proper protection.. maybe even a breathing mask.
instead of using regular fan screws that cut threads into the fan.. what about using a screw and nut and rubber washers to isolate the fan from the bolt, nut, and case. and are those rubber mounts, where u squeeze it through the case then through teh fan to hold the fan against the case very good.. does anyone see any problems with that?
You know, there is an edit button to add to your original post... anyhow, what you describe for fan mounting is known as "soft mounting" the fan. Search and you'll find lots of different ways of doing this, with ear grommets, silicon thingies, pieces of foam, etc. Usually, the softer, the better.
You should try to seal any space between the fan and the case. I usually use "draft strips": soft rubber strips with an adhesive side, meant to seal cracks between doors and stuff. Comes in different thicknesses, very handy.
The minium size of the fan hole should be slightly larger than the diameter of the fan blades, because if the airflow from these blades hits the case edge on the way in or out this will cause audible turbulence. I usually cut an octogonal shape with 4 large and 4 small sides whenever the hole is not in sight.
You should try to seal any space between the fan and the case. I usually use "draft strips": soft rubber strips with an adhesive side, meant to seal cracks between doors and stuff. Comes in different thicknesses, very handy.
The minium size of the fan hole should be slightly larger than the diameter of the fan blades, because if the airflow from these blades hits the case edge on the way in or out this will cause audible turbulence. I usually cut an octogonal shape with 4 large and 4 small sides whenever the hole is not in sight.
-
- Posts: 237
- Joined: Tue Nov 11, 2003 6:48 am
- Location: Gothenburg, Sweden
- Contact:
Aluminum is much easier and softer the cut with anything compared to steel. Depening on the alloy however you can get some that are really uh.. prone to burring, so be sure to de-burr afterwards. (Since aluminum is softer you can also deform the hole more easily, to be more carefull when cutting compared to steel.jtcb wrote:Is Aluminum easier to cut than metal? I want to cut out the top blowhole and the back fan grill on my Lian-Li PC65. I will be using tin snip. Is it possible?
Well, I did it, and BOY are my forearms tired! Tin snips are damn tiring.
I was about 1mm away from MESSING it all up.
I was cutting the hole in the AMB, and stupid me forgot to find out where that supporting bar was! So when Im refitting the case, I say "oh crap." Only to find out that the duct that I inserted was 1mm away from the bar.
Close call!
PS. To those doing their first tinsnipping: Wear gloves. I've got two angry fingers that are yelling at me through thick callouses.
But boy does it look professional.
Thumbs up.
I was about 1mm away from MESSING it all up.
I was cutting the hole in the AMB, and stupid me forgot to find out where that supporting bar was! So when Im refitting the case, I say "oh crap." Only to find out that the duct that I inserted was 1mm away from the bar.
Close call!
PS. To those doing their first tinsnipping: Wear gloves. I've got two angry fingers that are yelling at me through thick callouses.
But boy does it look professional.
Thumbs up.
Question :
What is a good method to cover the edges that is low profile (unllike the rubber tubing i see from coolcases.com). I want something that hugs the metal tightly. People use some sort of automotive lining, but i'm not sure what its called. Ideas?
I'm asking because since I tin snipped my fan holes, the edges arent perfect and are ugly.
What is a good method to cover the edges that is low profile (unllike the rubber tubing i see from coolcases.com). I want something that hugs the metal tightly. People use some sort of automotive lining, but i'm not sure what its called. Ideas?
I'm asking because since I tin snipped my fan holes, the edges arent perfect and are ugly.
-
- SPCR Reviewer
- Posts: 8636
- Joined: Sat Nov 23, 2002 6:33 am
- Location: Sunny SoCal
Anything wrong with the way this molding looks?. It's real cheap and is available from mnpctech.com and bestbyte.com.tay wrote:Question :
What is a good method to cover the edges that is low profile (unllike the rubber tubing i see from coolcases.com). I want something that hugs the metal tightly.
bestbyte.net, not bestbyte.com. Got some for myself a couple of weeks back.Ralf Hutter wrote:Anything wrong with the way this molding looks?. It's real cheap and is available from mnpctech.com and bestbyte.com.
Thanks Ralf & lenny. That is exactly what I had in mind (nice cablegami btw lol).
I like bestbyte.net, they have good prices. SVC hasnt shipped one of my orders for 4 days, I am gonna try and cancel and call bestbyte. BTW theyre also at http://www.bestbyteinc.com
I like bestbyte.net, they have good prices. SVC hasnt shipped one of my orders for 4 days, I am gonna try and cancel and call bestbyte. BTW theyre also at http://www.bestbyteinc.com
-
- SPCR Reviewer
- Posts: 8636
- Joined: Sat Nov 23, 2002 6:33 am
- Location: Sunny SoCal