Enclosures and acoustic damping to help quiet them.
Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Devonavar
-
shaolin95
- Posts: 8
- Joined: Wed Dec 12, 2007 8:17 pm
Post
by shaolin95 » Tue May 13, 2008 9:39 am
Hi!
I need a full HTPC ATX case that fits my Scythe Ninja and no windows or any other LEDs as I want it to be totally black and dark. I like my HT room pitch black.
Its an OCed 2160 so air flow is important as well.
-
jeepescu
- Posts: 45
- Joined: Tue Aug 15, 2006 10:58 am
- Location: montreal
Post
by jeepescu » Thu May 15, 2008 6:24 am
I am very curious if such a thing exists, as I have been (and still am) looking for one also.
AFAIK, the minja is the way to go for this type of case (CM28x or others with <120mm fans), otherwise, the case will have to sit vertically (Antec Solo or similar).
-
shaolin95
- Posts: 8
- Joined: Wed Dec 12, 2007 8:17 pm
Post
by shaolin95 » Thu May 15, 2008 7:00 am
Well, it seems we are out of luck....I will probably just get a p182 or something like that...I wanted the Chakra or Phoenix due to their big 250mm fan but it seems the fan takes too much space thus making Ninja installation impossible.
-
jeepescu
- Posts: 45
- Joined: Tue Aug 15, 2006 10:58 am
- Location: montreal
Post
by jeepescu » Thu May 15, 2008 7:27 am
What made you exclude the minja out of your plans ?
I have still not made a decision yet, and was interested in someone else's arguments.
-
shaolin95
- Posts: 8
- Joined: Wed Dec 12, 2007 8:17 pm
Post
by shaolin95 » Thu May 15, 2008 7:38 am
I got my HTPC already running with my Scythe Ninja so I dont want to buy more parts..heck, I dont even want to remove the HS...I want a quick transfer of parts to my new case.
-
mumford
- Posts: 21
- Joined: Sat Oct 20, 2007 1:17 pm
Post
by mumford » Thu May 15, 2008 11:18 am
Maybe a 4U rackmount server case.
-
shaolin95
- Posts: 8
- Joined: Wed Dec 12, 2007 8:17 pm
Post
by shaolin95 » Thu May 15, 2008 11:35 am
Interesting but wouldnt 7" still be a bit smaller than what I need? I am still trying to figure that one out though.
-
NyteOwl
- Posts: 536
- Joined: Wed Aug 23, 2006 7:09 pm
- Location: Nova Scotia, Canada
Post
by NyteOwl » Thu May 15, 2008 11:43 am
Check out the Coolermaster CM Media 280 series cases. They should be tall enough to handle a Ninja.
-
mumford
- Posts: 21
- Joined: Sat Oct 20, 2007 1:17 pm
Post
by mumford » Thu May 15, 2008 12:24 pm
shaolin95 wrote:Interesting but wouldnt 7" still be a bit smaller than what I need? I am still trying to figure that one out though.
It fits just fine. Also, the acron nuts on the top of a Ninja are purely cosmetic. You can even remove them, if you need more room.
-
shaolin95
- Posts: 8
- Joined: Wed Dec 12, 2007 8:17 pm
Post
by shaolin95 » Thu May 15, 2008 12:33 pm
It woulnd be the first time I do something like that as I had to do that and worst to my accelero S1 vga cooler because it wouldnt fit due to my water cooling tubing setup.
So I take it that 7" is the minimum I am looking for? Would that be from wall to wall or from mobo tray to wall?
-
mumford
- Posts: 21
- Joined: Sat Oct 20, 2007 1:17 pm
Post
by mumford » Thu May 15, 2008 12:47 pm
shaolin95 wrote:
So I take it that 7" is the minimum I am looking for? Would that be from wall to wall or from mobo tray to wall?
I don't have the spec in front of me. But I think Ninja is only a bit over 6". Mobo usually sits on a standoff. So, you are looking at another 3/8" for the mobo and the standoff. 7" should be a tight fit. Again. I reemphasized that you can remove the acron nuts. So, you should have plenty of room.
Just pick the server case that you like, and a shop with good return policy.
I would go by "look". Pick something that you like.
This is what I have. Newegg even ship freely.
http://www.newegg.com/Product/Product.a ... _-11182566