Help me safely lap a scuffed Scythe Ninja hsf

Cooling Processors quietly

Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Lawrence Lee

Post Reply
Posts: 413
Joined: Sun Nov 02, 2003 2:26 pm

Help me safely lap a scuffed Scythe Ninja hsf

Post by mshan » Mon Jun 11, 2007 2:21 pm

I recently bought a 2 week old Scythe Ninja HSF and it arrived with several scuffs on it's copper interface:


I think it got damaged in transit because the seller left one of the mobo brackets resting against this surface and I think it rubbed against it in transit, producing those three linear scratches in the top of the photo above.

I'm thinking of getting this lapping kit from ( ) to eliminate those scratches.

I've never lapped a hsf before, so what should I know in terms of things to avoid and hints to do it right? e. g. how securely do those Ninja brackets clamp the hsf to the mobo (I'm using socket 939) and is it possible to sand off too much, leaving a gap that can only be filled with excess application of Artic Silver Ceramique?

Also, is it safe to rinse the hsf under running water and then let it completely dry out for several days to make sure there are no metal filing that could short out a mobo?

Posts: 1201
Joined: Tue Aug 23, 2005 1:53 pm
Location: Plymouth, MI

Post by psiu » Mon Jun 11, 2007 5:33 pm

I don't know anything about the lapping, but a good swishing of water and a few hours to dry would be fine--it's metal, not a sponge ;) Blow some compressed air through for kicks afterwards and wipe it with some 99% isopropyl alcohol.

Mr Evil
Posts: 566
Joined: Fri Jan 20, 2006 10:12 am
Location: UK

Post by Mr Evil » Mon Jun 11, 2007 6:21 pm

I'm sure that kit is usable, but going all the way to 2500 grit is way beyond the point of diminishing returns. You'd be lucky to measure any difference in temperature past 800, let alone a worthwhile one.

Posts: 413
Joined: Sun Nov 02, 2003 2:26 pm

Post by mshan » Mon Jun 11, 2007 6:35 pm

Could I damage the hsf with overzealous use of the 220 grit stuff (e.g. remove enough copper that the heat sink doesn't press against the hsf like Scythe intended?)

Posts: 525
Joined: Mon Feb 07, 2005 11:57 pm
Location: Seattle, WA

Post by dfrost » Tue Jun 12, 2007 9:19 am

It is possible to create a convex surface if you hold the heatsink by the 'top,' which allows the tower to tip as you're sliding it over the sandpaper. I'd suggest holding it as close to the bottom as possible by sticking your hand through below the fins.

Make sure that you keep the sandpaper wet, and rinse HS and sandpaper frequently.
[size=75][color=blue]P4 3.0C, XP-120 w/ Papst 4412F/2GL fan @6-11V, Abit AI7, NB47J HS, 4x512Mb Corsair TwinX RAM, soft mt'd Samsung SP2004C & HD321KJ SATA HDDs
Sonata w/ Mk II front panel, fans: Nexus exh @8-12V & YL in @5V, Seasonic S12-430, passive 9600 Pro w/ modified VM-101, LG CD/DVD burner
Old ears, electronically assisted[/color][/size]

Posts: 7431
Joined: Thu Oct 06, 2005 4:36 am
Location: Monterey Bay, CA

Post by CA_Steve » Wed Jun 13, 2007 4:44 am

...and the sandpaper is placed on an ultraflat surface. I used the glass out of a picture frame.

Posts: 16
Joined: Wed Aug 23, 2006 9:25 pm

Post by nikkai » Thu Jun 14, 2007 3:38 am

Click for instructions

There are several guides on the net. The above is an example.[/url]

Posts: 254
Joined: Mon Oct 11, 2004 9:43 am
Location: Sweden

Post by Kaleid » Thu Jun 14, 2007 3:54 am

i5 4670k (@4.2), Asus Z87-C, Mugen 2 revB (500rpm), Club 3d 280x with AC S1+ (700+500rpm), 24GB Kingston 1600Mhz, Crucial MX100 512GB SSD, 4TB+3TB WD Green (in softm. Scythe quietdrives), Soundblaster Z, Asus MG279Q, Corsair RM650i, Antec p180 (2x500rpm slipstream)

Posts: 740
Joined: Sun Oct 20, 2002 10:32 am
Location: Melbourne, Australia

Post by alleycat » Thu Jun 14, 2007 6:27 am

Seriously, I wouldn't worry about it. Unless the scratches have produced ridges that prevent the HS from sitting properly on the CPU, I doubt that they would make any noticeable difference. I suggest you try using the HS as it is, and if you aren't happy with the results you can reassess the situation.

I've done lapping before and doubt that it helped much. It's probably more important just to get the HS mounted properly with the right amount of paste. It would be a pain in the arse to lap that Ninja, and you wouldn't want to get it wrong.

Posts: 26
Joined: Thu Aug 03, 2006 7:06 pm

Post by vanhelmont » Thu Jun 14, 2007 10:55 am

I agree. The scratch area is so small it won't matter, unless they are deep scratches with raised ridges at their sides.

If they really worry you, I would say get a sheet of 400 or maybe even 600 wet or dry sandpaper, put it on a smooth surface, like glass, hold the heat sink near the bottom so it stays straight, use some water and moderate force, and you don't need to make the scratches disappear, just get rid of any ridges at the side. Less is more.
An idle processor is the devil's workshop.

Contribute to medical research by putting your idle processor to work on [url=]folding@home![/url]

Post Reply