Page 1 of 2

Magnetic rotor for case fans... Interesting

Posted: Mon Feb 23, 2004 8:26 am
by sgtpokey
I completely missed this blurb the last few days 'cause I thought they were talking about Maglev trains or something, but apparently Sunon was showing a case fan where the blades are rotated through magnets, instead of the physical contact of a traditional rotor and bearings:

The other one that caught my eye is Sunon. It had a big sign touting Maglev fans. Rather than a motor, shaft, and the associated noise, the Sunon fans magnetically levitate the rotating parts. It claims lower noise, more precision, and just about better everything. I wasn't able to play with one during the show, and can't say much more than the fact that they do indeed spin.
http://www.theinquirer.net/?article=14293

Your link is wonky...

Posted: Mon Feb 23, 2004 9:49 am
by NeilBlanchard

Posted: Mon Feb 23, 2004 11:46 am
by sgtpokey
Thanks for catching the html typo Neil, I've edited the link...

Information from Sunon on maglev fans

Posted: Mon Feb 23, 2004 1:34 pm
by icancam

Posted: Mon Feb 23, 2004 3:52 pm
by HammerSandwich
SVC has had this maglev fan for some time now. I got one in late summer. It's an interesting piece: very low friction indeed and fairly low mechanical noise. It is, of course, a high-RPM screamer, but it undervolts nicely. I'd love to see a sub-2000 RPM 120mm version.

Maglev fan sizes

Posted: Mon Feb 23, 2004 4:53 pm
by icancam
It appears that the largest axial fan that Sunon makes in the maglev series is 70mm. They seem to be concentrating on smaller diameter axial fans but do have a 120mm blower type. Apparently, the maglev fans were introduced in 1999 and millions have been produced.

It would be great to see the maglev technology applied to slow turning and larger diameter axial fans in the 80, 92, and 120mm sizes.

A most interesting feature of the magnetic levitation technology is that it allows positioning of an axial fan at any angle without being concerned about uneven bearing wear.

Could magnetic levitation bearing technology ever be used in hard drives to further reduce their noise levels and allow mounting at any angle?

Re: Maglev fan sizes

Posted: Sun Mar 07, 2004 6:11 am
by lm
icancam wrote: Could magnetic levitation bearing technology ever be used in hard drives to further reduce their noise levels and allow mounting at any angle?
Since hdds are magnetic storage would such magnetic fields be a problem?

Posted: Sun Mar 07, 2004 8:59 am
by Talz
These are not going to cause any problems like that, there's a magnet in each hard drive that is hundreds of times stronger, maybe thousands lol.

Posted: Sun Mar 07, 2004 9:20 am
by DryFire
hd magnets are very power full. Some of the most powerfull I've seen for that size.

Posted: Sun Mar 07, 2004 11:01 am
by AndrewC
Just found an 80 mm version.
http://www.adpmods.com/xcart/customer/p ... =92&page=1

Only 2300 RPM so it might have more undervolted uses.

Posted: Sun Mar 07, 2004 11:06 am
by MikeC
AndrewC wrote:Just found an 80 mm version.
http://www.adpmods.com/xcart/customer/p ... =92&page=1

Only 2300 RPM so it might have more undervolted uses.
ADPMODS promised a few samples. See their post in the Calling all Good Fans thread.

Posted: Sun Mar 07, 2004 11:25 am
by Talz
I'm thinking about buying some to try them out myself. I was impressed with the MagLev fan on my MCX-159.

Posted: Sun Mar 07, 2004 10:12 pm
by al bundy
MikeC wrote:ADPMODS promised a few samples. See their post in the Calling all Good Fans thread.
Excellent - can't wait to get your feedback on these.

8)

Posted: Sun Mar 07, 2004 10:52 pm
by Edward Ng
I also own an MCX-159 and took the little fan off because of its noise level; it never crossed my mind that it's some sort of special type of fan. Maybe I'll go find it and take a closer look at it...

-Ed

Posted: Sun May 02, 2004 11:56 pm
by Trip
http://www.3dcool.com/?module=product&sku=SMLFAN is selling 70mm and below. I wonder how they handle time, heat, and shock.

Posted: Thu Jun 24, 2004 9:29 pm
by DrCR
Any update guys? When undervolted is is in the same tier as the Japanaflo, Evercool, Global, etc.?

Sunon makes this MagLev series up to 92mm axial and 120mm blower.


DrCR


___________

Posted: Thu Jun 24, 2004 10:59 pm
by burcakb
Globe (manufacturers of Acoustifan and i think evercool fans) are also working on magnetic bearing fans. Only 80x25 at the moment though.

It's on testing stage yet and no dBA numbers are around. But it seems for a low-flow 2000 rpm fan, the CFM and static pressure values are lower than a regular fan.

So unless a 3000 rpm high-speed magnetic fan has the same noise profile of a 2000 rpm normal fan, I don't see much to be excited about - well, maybe the lifetime.

Posted: Fri Jun 25, 2004 4:29 am
by Edward Ng
Manufacturers of AcoustiFan and Enermax fans. Not sure 'bout Evercool, but it won't surprise me. Globe is actually quite big.

-Ed

Posted: Thu Jul 01, 2004 11:53 am
by mpteach
Q1 Do these fans have a 3wire rpm tach outut?

Q2 When are these fans going to have an official review by SPCR?

Posted: Thu Jul 01, 2004 12:32 pm
by DrCR
mpteach wrote:Q1 Do these fans have a 3wire rpm tach outut?

Q2 When are these fans going to have an official review by SPCR?

Some have the 3-pin with tach, others the standard 4-pin. Just make sure you know which one your ordering.


As for an official review... that would be awsome. :) It might be hard to find a 80mm vendor that would be willing to loan it to SPCR for a review though. :?


DrCR


_____________

Posted: Thu Sep 16, 2004 7:40 pm
by Kaizer
Hi All,

I have several 80x25mm Sunon Maglev (the low speed version KDE1208PTV3) and I've tried them both as case fans & CPU fans. At 12 volts, these fans are somewhat noisy but the pitch of the sound (from the motor) is quite low and a large portion of the noise is actually the "whooshing" sound of air exiting the fan blades.

I can tell u that the KDE1208PTV3 is louder than the coolermaster rifle-bearing LED fans at 12V but cools my stock 2500+ 2 degrees better than the coolermaster (on an ALX-800) despite it's lower fan speed (2500RPM, not 2300RPM as advertised vs. Coolermaster's 2600 rpm, not 2500 as advertised). I had no experience with the L1A :( .
At 7V, the Maglev is quiet but still audible (it makes a low wuuuuuuu sound).
At 5V, the Maglev is very quiet and you have to get pretty close to your PC case in order to hear (it makes a low zzzzzzzzzz sound, and it's not the snoring sound you hear at night :wink:)
Right now, I am using these fans as my intake. If you use them as exhaust or for the CPU, the Maglev would sound quieter.

I've tested my low speed Maglev against the Coolermaster Rifle-bearing LEDs and the Vantec Stealth for vibration and the Maglev bested both, as it made the least amount of rattling when mounted on my ALX-800. (The Stealth was the worst of the three) The levitated fan hub does makes the fan vibrate less.

If you're looking for some performance but still relatively low noise cooling, you should consider the low speed Maglev (especially as CPU fans for the Thermalright heatsinks since direct fan to metal contact is involved). The Maglev at 5V is nearly silent but it might not be quiet enough for some of you. Also, if you living in BC or in the Vancouver area, you should get them from Anitec (http://www.anitec.ca/?mode=product_detail&pid=389) for only 3 bucks each!!!! (for the 3 pin version that is) I bought 4 & had absolutely no regrets!

Posted: Thu Sep 16, 2004 8:44 pm
by sthayashi
Does MikeC have one of these to review in his great fan test?

Posted: Thu Sep 16, 2004 10:27 pm
by MikeC
sthayashi wrote:Does MikeC have one of these to review in his great fan test?
yes, I think so.

Posted: Fri Sep 17, 2004 5:17 am
by DrCR
Wow, this is an old thread. lol

Thanks for the update Kaizer. You really need to pick up a Japanaflo L1A. :wink: If only to give everyone a frame of reference. You can get it here from jab-tech. I’m familiar with the Vantec Stealths so the MagLevs sound at least decent. And $3 isn’t that bad at all (I’m in the States though)!


Personally, I've very curious with respect to the MagLev120mm squirrel type blower as I'm looking for two 120mm fans for my heatercore. I plan on getting Papst 4412 axials right now, but a blower design is inherently better in a high restrictive environment. Maybe I should go ahead and buy both. lol


MikeC, would you be interested in including the 120mm MagLev blower (not axial) in your review? If so, PM me.


DrCR


__________

Posted: Fri Sep 17, 2004 5:24 am
by Edward Ng
DrCR, where will you be buying the 120mm blowers from? I did a search today and was only able to find 80mm axial; did't see anything larger than 80mm.

Actually, I placed an order for 4 of the 80mm pieces.

Posted: Fri Sep 17, 2004 7:12 pm
by DrCR
I first mentioned the 120mm blower here:
http://forums.silentpcreview.com/viewto ... torder=asc

Currently I do not know of any enduser vendor selling the MagLev 120mm blower. There's a group of computer peers I know who might be able to get it through their computer shop. If not, I'll probably look for it through work (I work in Information Technologies Procurement).

To be honest I haven't had the time to do a real good search for it. Physical Chemistry is keeping me busy lol.


DrCR


___________

Posted: Fri Sep 17, 2004 7:14 pm
by DrCR
Duh, then again, how about here:
http://www.directron.com/12plb2.html

:D


Edit:

An alternative source:
http://www.buyextras.com/b12dc12vdoba.html

This vendor looks pretty good from the little feedback from resellerratings here, but I can personally recommend Directron. I'm sure most if not all here are familiar with Directron anyhow.


DrCR


__________

Posted: Fri Sep 17, 2004 7:21 pm
by Edward Ng
Hmm; that shape makes it seem sort of difficult to utilize...

I was thinking something more along ehe lines of the type of blower that Cooler Master used to have mounted to their Aero coolers.; this one has a small opening to the side, whereas the blower on the Aero coolers was an entire square opening to one side (in the case of the Aero coolers, the bottom side)...

Would take some ingenuity to come up with an effective use for this design, that's for sure.

Posted: Fri Sep 17, 2004 7:29 pm
by DrCR
Not really. Just a simple duct on the heatercore to the intakes like usual. The bolt holes are standard 120mm. The only difference would be having the air blowing out the side of your case. :)

I've actually thought about using an undervolted car heatercore blower from a Camry or something, but I doubt it would be sufficently quiet for me even when undervolted.

Camry Blower Image

About 7" (~18cm) in diameter. That's not really the bad, the problem is the depth at about 4" (~10cm) if I remember correctly, perhaps even thicker. Obviously the Sunon's 35mm would be a lot narrower and easier to fit in.


DrCR


___________

Posted: Fri Sep 17, 2004 7:34 pm
by Edward Ng
[Thread highjack]

I see now, pulling...

But would this be in any way quieter than using a standard 120mm fan in a pull configuration? Or are you going for higher negative pressure, rather than silence?

Or perhaps you're going for some sort of in-between balance (not dead silent, but not loud, yet still moving plenty of air)? Such as my own water cooling rig, which is a gaming rig used with headphones, so I set a looser noise level constraint for that build, allowing me better flow rates for the massive overclock.

[/Thread Highjack]