Custom A64 Undervolting
Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Lawrence Lee
-
- Posts: 40
- Joined: Fri May 21, 2004 10:49 am
Custom A64 Undervolting
I have an Athlon64 3200+ running on a K8V deluxe. I've had my share of troubles with the system but I picked it because the board is passively cooled. Anyway, I've been lurking here for quite some time and wanted to share some of my experience. Thanks for all the wonderful posts and reviews on this site. I'm hooked on silencing now!
My CPU was purchased in February so it defaults to the older version of Cool n Quiet (800Mhz low power state at higher voltage). I am running Windows Server 2003 and the CnQ driver doesn't seem to work properly. My cooler is a Swiftech MCX6400V. I was running a Silenx thermistor fan and am now trying it with a Panaflo L1A (PWM controlled).
The cooler is quiet and the CPU usually stays between 55-60C when Folding @ default voltage + silenx. I tried to undervolt and was able to reduce Vcore to 1.4 volts reliably. This roughly 10% decrease dropped temps by ~4C. I couldn't go any lower without getting Machine Check Error warnings.
I noticed ClockGen and decided custom underclock my box.
http://www.cpuid.com/clockgen.php
After re-enabling CnQ in the Bios, I was able to get as low as 1.075 Volts @ 200x 7 (1.4 ghz). At this setting the CPU stays within 2 - 4C of "mobo temp" if the panaflo is @ 12V. The difference is much higher @ 7V--more like 10C. This isn't all too impressive except that the case temps have dropped too so the system is much cooler overall. I suppose the swiftech isn't exactly the best ultra-low airflow cooler. Maybe next time I'll try an exhaust-ducted Alpha. Of course, my next mission is to reduce HD noise! My 15k3 scsi drive might force me to apply some form of accoustic damping to my 3700BQE.
Anyway, I just wanted to say that you are not limited by the default CnQ settings when undervolting your A64. The advantage of this method is you get to choose exactly when (and by how much) your box speeds up. My box was stable and quiet before, but the temps made me a little uneasy. Now my temperatures are awesome.
*Note: The temps are here just to give a general idea of the reduction that is possible. There are no hard temperature comparisons because my system is always in state of change and the only tool I have for temp monitoring is Asus Probe software. I swapped between Silenx and Panaflo fans and also reapplied AS5 last night.
My CPU was purchased in February so it defaults to the older version of Cool n Quiet (800Mhz low power state at higher voltage). I am running Windows Server 2003 and the CnQ driver doesn't seem to work properly. My cooler is a Swiftech MCX6400V. I was running a Silenx thermistor fan and am now trying it with a Panaflo L1A (PWM controlled).
The cooler is quiet and the CPU usually stays between 55-60C when Folding @ default voltage + silenx. I tried to undervolt and was able to reduce Vcore to 1.4 volts reliably. This roughly 10% decrease dropped temps by ~4C. I couldn't go any lower without getting Machine Check Error warnings.
I noticed ClockGen and decided custom underclock my box.
http://www.cpuid.com/clockgen.php
After re-enabling CnQ in the Bios, I was able to get as low as 1.075 Volts @ 200x 7 (1.4 ghz). At this setting the CPU stays within 2 - 4C of "mobo temp" if the panaflo is @ 12V. The difference is much higher @ 7V--more like 10C. This isn't all too impressive except that the case temps have dropped too so the system is much cooler overall. I suppose the swiftech isn't exactly the best ultra-low airflow cooler. Maybe next time I'll try an exhaust-ducted Alpha. Of course, my next mission is to reduce HD noise! My 15k3 scsi drive might force me to apply some form of accoustic damping to my 3700BQE.
Anyway, I just wanted to say that you are not limited by the default CnQ settings when undervolting your A64. The advantage of this method is you get to choose exactly when (and by how much) your box speeds up. My box was stable and quiet before, but the temps made me a little uneasy. Now my temperatures are awesome.
*Note: The temps are here just to give a general idea of the reduction that is possible. There are no hard temperature comparisons because my system is always in state of change and the only tool I have for temp monitoring is Asus Probe software. I swapped between Silenx and Panaflo fans and also reapplied AS5 last night.
It's printed on the heatspreader, and CPU-Z tells you what stepping it detected.mikellpp wrote:How do you identify the CG stepping?SpyderCat
I can go down to 0.85 volts @ 5*200 = 1000 MHz with the CG stepping.
This is an awsome CPU.
And how does it differ from th 35 watt mobile Athlon 64 chip?
Here it is, running Prime95 and Folding at the same time.
CPU temps 38° (diode by MBM)
Know nothing about a mobile Athlon64, sorry
I found the AMD spec for CG stepping for Athlon64 3000It's printed on the heatspreader, and CPU-Z tells you what stepping it detected.
ADA3000AEP4AR
2000 MHz
1.50 V
57.8 A
89 W
0.31°C/W
1800 MHz
1.40 V
45.6 A
66 W
1000 MHz
1.10 V
18.0 A
22 W
i could not find any ADA3000AEP4AR for sale at newegg, pricewathc, etc.
I assume this is the Athlon64 you have. Where did you get it?
-
- Posts: 40
- Joined: Fri May 21, 2004 10:49 am
Haha, DAMN YOU!SpyderCat wrote:It's a pity you have the older stepping of this CPU.
I can go down to 0.85 volts @ 5*200 = 1000 MHz with the CG stepping.
This is an awsome CPU.
Have fun!
Instant BSOD/Reboot at around 0.9 volts for me! I guess that's what I get for buying a CPU before it is "mature."
-
- Posts: 216
- Joined: Mon May 24, 2004 10:42 pm
- Location: Canada
Have you tried dropping the speed down to 1 Ghz to see if you can't get vcore a bit lower still?hydroxyhydride wrote:Haha, DAMN YOU!SpyderCat wrote:It's a pity you have the older stepping of this CPU.
I can go down to 0.85 volts @ 5*200 = 1000 MHz with the CG stepping.
This is an awsome CPU.
Have fun!
Instant BSOD/Reboot at around 0.9 volts for me! I guess that's what I get for buying a CPU before it is "mature."
-
- Posts: 40
- Joined: Fri May 21, 2004 10:49 am
0.9V BSOD was @ 1 ghz
I may be able to take the Vcore a little lower but there seems to be a point of diminishing returns. I'm back at 1.4V experimenting with a ghetto duct I made from a 2-liter coke bottle--but it doesn't seem to be going so well. Rear exhaust is now the CPU intake and the front intake fan has been swapped so it is blowing out. CPU is cooler but I the system temp is up a lot. Maybe if I had a VGA Silencer instead of my ZM80C and I used an ALPHA to exhaust the CPU things would be better. However, these experiments are meaningless until I can quiet my hard drives. ...
I may be able to take the Vcore a little lower but there seems to be a point of diminishing returns. I'm back at 1.4V experimenting with a ghetto duct I made from a 2-liter coke bottle--but it doesn't seem to be going so well. Rear exhaust is now the CPU intake and the front intake fan has been swapped so it is blowing out. CPU is cooler but I the system temp is up a lot. Maybe if I had a VGA Silencer instead of my ZM80C and I used an ALPHA to exhaust the CPU things would be better. However, these experiments are meaningless until I can quiet my hard drives. ...
How low can you go?
For reasons illustrated in http://www.silentpcreview.com/article164-page1.html I was wondering what the minimum voltage/clock is with A64s. Are these systems useable for Word, etc at for example 0.8v/300MHz.
Mark
Mark
-
- Posts: 40
- Joined: Fri May 21, 2004 10:49 am
-
- Posts: 216
- Joined: Mon May 24, 2004 10:42 pm
- Location: Canada
Also, doesn't it kind of defeat the purpose of buying this lovely powerful 64-bit machine, to be running at 300 Mhz?hydroxyhydride wrote:Well the minimum multiplier I am able to find using ClockGen is 4 (which means 800 mhz). I don't think you can get the system at 300mhz as that would mean a multiplier of 1.5 --and I haven't found a way to make that happen yet.
I've just bought my first A64. It's Newcastle, DH7-CG. I was testing it to find lowest voltages on every freqency. I was satisfied if it pass one hour or more i prime95.
To be more precise, my mobo (Chaintech VNF3-250) overvolts a little bit under heavy load, but that overvolt is quite small 0.000V @~0.800V, 0.025V @~1.100V, 0.050V @~1.5V.
Here's graph:
To be more precise, my mobo (Chaintech VNF3-250) overvolts a little bit under heavy load, but that overvolt is quite small 0.000V @~0.800V, 0.025V @~1.100V, 0.050V @~1.5V.
Here's graph:
-
- Posts: 419
- Joined: Sun Sep 19, 2004 1:05 pm
- Location: Palo Alto, CA
-
- Posts: 419
- Joined: Sun Sep 19, 2004 1:05 pm
- Location: Palo Alto, CA
No, I have Newcastle - it's 130nm and Winchester (90nm) is not yet released for Socket 754.
The fact I can run my CPU at lower voltages than you is that I run it out of specification and you would be probably able to achieve similar voltages with your mobile (maybe even lower). Give it a try!
You can go much further than 1.6GHz with your CPU by riseing FSB. If you have week RAM that wouldn't go over 200MHz just put it in 166MHz mod. It will run at FSB*166MHz/200MHz and it would be about 200MHz if you overclock FSB to 240MHz. CPU would be on 1920MHz at that moment.
The fact I can run my CPU at lower voltages than you is that I run it out of specification and you would be probably able to achieve similar voltages with your mobile (maybe even lower). Give it a try!
You can go much further than 1.6GHz with your CPU by riseing FSB. If you have week RAM that wouldn't go over 200MHz just put it in 166MHz mod. It will run at FSB*166MHz/200MHz and it would be about 200MHz if you overclock FSB to 240MHz. CPU would be on 1920MHz at that moment.
I think the new mobile A64 have started to show up. They're called Oakville, not Winchester, right?
Does anyone know the OPN codes for these 35 W mobile 90 nm? I've found AMD3000BKX4LB but I'm really not sure what it is.
1.2 V should be the "Q", not "K" (ok, maybe they've changed Vcore just like they did with S939 90 nm, when looking at Fab51 it seems like they might use 1.35 V), and what is "LB"?? If it's a revision D core then it should be "B(x)", like "BI" AFAIK. I've found them here (also 2800+ and 2700+):
FrontierPC (Canada)
ITButikken (Denmark)
Verkkokauppa (Finland)
Also mentioned here:
Seagate
Chipworks
The problem is just how to find a S754 mobo that will work properly with BOTH 90 nm and mobile CPUs....
Does anyone know the OPN codes for these 35 W mobile 90 nm? I've found AMD3000BKX4LB but I'm really not sure what it is.
1.2 V should be the "Q", not "K" (ok, maybe they've changed Vcore just like they did with S939 90 nm, when looking at Fab51 it seems like they might use 1.35 V), and what is "LB"?? If it's a revision D core then it should be "B(x)", like "BI" AFAIK. I've found them here (also 2800+ and 2700+):
FrontierPC (Canada)
ITButikken (Denmark)
Verkkokauppa (Finland)
Also mentioned here:
Seagate
Chipworks
The problem is just how to find a S754 mobo that will work properly with BOTH 90 nm and mobile CPUs....