Radeon HD 4670: A perfect balance?

They make noise, too.

Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Lawrence Lee

Post Reply
Vicotnik
*Lifetime Patron*
Posts: 1831
Joined: Thu Feb 13, 2003 6:53 am
Location: Sweden

Post by Vicotnik » Thu Nov 20, 2008 2:04 am

Switched from a Sapphire 4670 512MB to a HIS 4670 512MB today and idle power consumption for the whole system went from 52W to 49W. :)
Stock bios on both cards so far. Now I can finally do some tweaking using RBE.

Matija
Posts: 780
Joined: Sat Mar 17, 2007 3:17 am
Location: Croatia

Post by Matija » Thu Nov 20, 2008 2:59 am

Maybe that's because Sapphire has higher-clocked RAM?

lechuck
Posts: 86
Joined: Mon Dec 04, 2006 11:57 pm
Location: EU

Post by lechuck » Thu Nov 20, 2008 3:14 am

@Vicotnik: I wish you'll have sucess with RBE tweaking.
Btw, you have excellent power consumption. Is that measured from the wall? Sure PSU is helping a lot. :)
But how do you handle 3D load?
Did you measure how much you have without 4670, or how much HIS cards adds to the power consumption?

@Matija: No, I'd say that's because Sapphire has no voltage regulation programmed in Bios.

Ksanderash
Posts: 353
Joined: Sat Oct 18, 2008 6:30 am
Location: Moldova, exUSSR

Post by Ksanderash » Thu Nov 20, 2008 4:12 am

Vicotnik
How do you measure AC wattage? I personally don't have TrueRMS multimeter and I wonder how you guys are getting with AC power :)

Vicotnik
*Lifetime Patron*
Posts: 1831
Joined: Thu Feb 13, 2003 6:53 am
Location: Sweden

Post by Vicotnik » Fri Nov 21, 2008 6:50 am

lechuck wrote:But how do you handle 3D load?
Did you measure how much you have without 4670, or how much HIS cards adds to the power consumption?
3D load is no problem now when I can modify the bios using RBE. I'm experimenting with underclocking and undervolting the 3D mode to have some headroom.
I haven't measured power consumption without the discreet graphics card.
Ksanderash wrote:Vicotnik
How do you measure AC wattage? I personally don't have TrueRMS multimeter and I wonder how you guys are getting with AC power :)
I use a kill-a-watt type of meter that plugs into the wall

TheSilentOne
Posts: 10
Joined: Sat Nov 29, 2008 11:31 pm
Location: Finland

Post by TheSilentOne » Sun Nov 30, 2008 12:49 am

Kriz wrote: According to RBE 1.15...

HD4670 idle clocks: 165MHz GPU / 250MHz RAM / 0.900v
HD4670 full speed: 780MHz GPU / 1000MHz RAM / 1.250v

Now for some more power testing with the Seasonic SS-300SFD 300W PSU...

Using onboard GPU: 41W Idle / 69W Load (Prime95 Small FFTs)
Using HIS HD4670: 54W Idle / 81W Load (Prime95 Small FFTs)

So, it's still around 12-13W extra for my particular configuration.

More to come next week.
Hi,
I have Sapphire Radeon 4670 512Mb. With default settings the card has quite high idle power usage, 20W.

4850e + 780g on idle 49W
4850e + 4670, 780g disabled = 69W
So, 4670 was +20W on idle, nowhere near the SPRC's tested +4W.

I made a profile, and was able to set the idle settings at:
GPU 165Mz, Memory 500Mhz, Voltage 0,9V. The idle power usage was 63w = +14W. (I cannot verify that the voltage was actually lowered )

So, it seems I cannot get better idle power by switching to HIS 4670, because your card seems to take also +13W idle.

Is there anyone who has a card that takes that +4W that SPCR tested? Or is this +4W vs. my +14W only a result of lower idle power usage of my 780g vs. SPCR's i945Ga? Main reason for me buying this card was SPCR's test...

Ksanderash
Posts: 353
Joined: Sat Oct 18, 2008 6:30 am
Location: Moldova, exUSSR

Post by Ksanderash » Mon Dec 01, 2008 2:25 am

TheSilentOne wrote: So, it seems I cannot get better idle power by switching to HIS 4670, because your card seems to take also +13W idle.
My Force3D 4670 idles at the same 13.3W (1.29V on GPU, 1.8V on RAM). Maybe (I'm again with this version) the card simply don't switch to VID that RBE is providing? Hm, I'll do some tests on this, to be shure.
Is there anyone who has a card that takes that +4W that SPCR tested? Or is this +4W vs. my +14W only a result of lower idle power usage of my 780g vs. SPCR's i945Ga? Main reason for me buying this card was SPCR's test...
Oh yeah, the magic card SPRC were tested... I like it too :)

There can't be so much difference, furthermore the 780G has a lower idle consumption than 945G.

Kriz
*Lifetime Patron*
Posts: 51
Joined: Tue Sep 02, 2008 10:16 am
Location: Australia

Post by Kriz » Mon Dec 01, 2008 2:42 am

I've also been wondering about that 4W idle reading, it sounds a little too low.

If our cards are almost the same as the one used in the review, and our numbers are correct, then I can see a SPCR review where a HD4550 or HD4650 appears to use no power, or has the ability to generate it's own. :lol:

After doing a little digging, I've found this Intel PDF document (link) stating that with the G965 chipset, it is able to disable it's IGP when an external graphics card is installed, resulting in a TDP reduction of 9W, bringing it to the same TDP of the P965 (Page 14, 2.4.3 - Note 3.).

Also, with the 945G I found in this PDF document (link) that the IGD (Integrated Graphics Device) cannot operate with an external PCI Express graphics device (Page 257, 10.6.3 - Note).

With these facts in mind, perhaps the 945G also disables it's IGP, resulting in a TDP reduction from 22.2W to the same level as the 945P TDP of 15.2W? And following that same line of reasoning, maybe the TDP difference is very close to the IDLE difference of 7W?

I'm just making guesses here, I know that TDP has nothing to do with IDLE watts, but in this case it could partially explain those low numbers.

I wonder if Lawrence Lee still has that HD4670 from the review? It would be interesting to see it's idle power on a non-Intel chipset motherboard.

DifferentBreed
Posts: 1
Joined: Mon Dec 01, 2008 4:16 am
Location: UK

Post by DifferentBreed » Mon Dec 01, 2008 4:26 am

Hi All

Ive recently bought the ASUS 4670 to fit into my new shuttle sx48p2 deluxe.
The card fits ok but because of the big heatsink and fan it means that it takes up the other pcie slot.Also cables keep getting jammed into the fan, so I thought id buy the zalman vf900 and fit that.When I took of the stock heatsink there was all this white gluey stuff which was still fluid.How can I get this off? Ive ordered some articlean which is coming with my vf900.The exposed GPU doesnt seem to have a metal cover on it so Im bit worried about how to clean it properly.Does anyone have any tips or advice with cleaning the GPU , plus any experience with a shuttle SFF box, an ASUS 4670 and a zalman vf900.

Sorry about the lengthy post, but its my first go and im a total noob when it comes to modding video cards.

Matija
Posts: 780
Joined: Sat Mar 17, 2007 3:17 am
Location: Croatia

Post by Matija » Mon Dec 01, 2008 6:28 am

X-bit Labs measured the PowerColor card at 8W in idle...

Why all the differences?

BTW, I bought a Sapphire 4670 today, and I'm going to fit a HR-03 on it. Wish me luck.

QuietOC
Posts: 1407
Joined: Tue Dec 13, 2005 1:08 pm
Location: Michigan
Contact:

Post by QuietOC » Mon Dec 01, 2008 7:38 am

Matija wrote:X-bit Labs measured the PowerColor card at 8W in idle...

Why all the differences?
1. Different way to measure power draw
2. Different cards with different power management

Notes for 1.
1a. X-bit is measuring DC voltage/amps to video card.
(neglects power saved/used by other components)
1b. SilentPCReview measures total AC power usage.
(sums power saved/used by other components.)

Method 1a should be accurate for the specific video card in any system.

Method 1b is more accurate to actual power use, but the numbers are specific to the particular motherboard and power supply used during the testing. A negative power change from IGP to a discrete card is possible under method 1b.

Matija
Posts: 780
Joined: Sat Mar 17, 2007 3:17 am
Location: Croatia

Post by Matija » Mon Dec 01, 2008 11:52 am

Installed the card.

Damn, the thing is loud. Under load it's actually okay, but it's idle that's killing me. Manual fan speed control = fail.

I'll test the HR-03 on it eventually. I thought about doing it over the weekend, but the noise is killing me, so I might try tomorrow.

lechuck
Posts: 86
Joined: Mon Dec 04, 2006 11:57 pm
Location: EU

Post by lechuck » Tue Dec 02, 2008 12:19 am

@QuietOC: So, to make better idea how much a real system uses, SPCR should modify method 1b. Modern IGP can use 5W or more
and that should be taken into account. SPCR should find an old discrete 2D only card and measure the actual power use.
Then they could estimate IGP consumption and then correct VGA consumption.

My 'reference' discrete card is old Matrox Millenium. I don't know it's power consumption, but it can't be very high. The card does not
even have a heatsink! And as this was 'high-end' card at that time it's possible that other models consume even less.


@Matija: Post results for HR-03 and pictures also. :)

Fungi
Posts: 95
Joined: Fri Dec 01, 2006 1:27 pm

Post by Fungi » Tue Dec 02, 2008 2:44 am

Matija wrote:Installed the card.

Damn, the thing is loud. Under load it's actually okay, but it's idle that's killing me. Manual fan speed control = fail.

I'll test the HR-03 on it eventually. I thought about doing it over the weekend, but the noise is killing me, so I might try tomorrow.
Anything bigger/better than the Accelero S2 (not S1) is overkill IMO. :lol:

Matija
Posts: 780
Joined: Sat Mar 17, 2007 3:17 am
Location: Croatia

Post by Matija » Tue Dec 02, 2008 2:50 am

The HR-03 is a leftover from my EPIC FAIL in trying to passively cool the x1950 this card replaced...

lechuck
Posts: 86
Joined: Mon Dec 04, 2006 11:57 pm
Location: EU

Post by lechuck » Tue Dec 02, 2008 3:46 am

Why not overkill?

I think HR-03 should be better, as it brings heat to the back of the card, so it can go up with convection ...

Chang
Posts: 129
Joined: Mon Oct 11, 2004 12:26 pm

Post by Chang » Tue Dec 02, 2008 9:11 am

Matija wrote:Damn, the thing is loud. Under load it's actually okay, but it's idle that's killing me. Manual fan speed control = fail.
When you say fail, do you mean that manual fan speed control doesn't work or that it doesn't get it quiet enough for your system? I hope it's the latter as the Sapphire card is on my "list" of cards for which manual fan speed control works. . .

Matija
Posts: 780
Joined: Sat Mar 17, 2007 3:17 am
Location: Croatia

Post by Matija » Tue Dec 02, 2008 9:54 am

Doesn't work, at least not through CCC.

BTW, I'm not sure if the HR-03 can be installed in the wrap-around mode... The fan connector might get in the way :| I'll know more when I get to the replacement process...

lechuck
Posts: 86
Joined: Mon Dec 04, 2006 11:57 pm
Location: EU

Post by lechuck » Tue Dec 02, 2008 12:23 pm

It might go.

I saw this problem before and I asked Thermalright support and they replied:
...if you make the cooler at the back of the card, it can be a passive cooler, the distance will be around 7mm
between the PCB and heat pipes, about the fan connector, HR-03 Rev will have no problem.

Aris
Posts: 2299
Joined: Mon Dec 15, 2003 10:29 am
Location: Bellevue, Nebraska
Contact:

Post by Aris » Tue Dec 02, 2008 1:57 pm

70w load? Still doesnt beat my 50w load 256mb 8800GT. 8800GT still outperforms it also.

Matija
Posts: 780
Joined: Sat Mar 17, 2007 3:17 am
Location: Croatia

Post by Matija » Tue Dec 02, 2008 10:25 pm

What?

8800 GT is ~80W load and ~35W idle.

This card is ~50W load and ~10W idle.

lechuck
Posts: 86
Joined: Mon Dec 04, 2006 11:57 pm
Location: EU

Post by lechuck » Tue Dec 02, 2008 10:33 pm

@Aris: You know that's not true! Do a little research before you post.
Your 8800GT sucks with the power consumtion. It has idle at 35W DC and 3D load at 80W DC.
We are talking here about a 4670 card that has idle at 9W DC and 3D load 47W DC.
(from xbitlabs)

So buy two 4670 cards and you'll have lower power consumtion as 8800GT while not gaming
and better fps while gaming.
Last edited by lechuck on Wed Dec 03, 2008 5:50 am, edited 1 time in total.

TheSilentOne
Posts: 10
Joined: Sat Nov 29, 2008 11:31 pm
Location: Finland

Post by TheSilentOne » Wed Dec 03, 2008 1:30 am

I have a DC clamp meter, so I can measure the DC idle power, but I'm not doing it before I get a waterblock for this card.
Does anyone know if the Zalman waterblock for 3850/3870 card is ok for 4670? http://www.zalman.co.kr/ENG/product/Pro ... sp?Idx=286

Vicotnik's idle power dropped -3W when changing from Sapphire to HIS. What was the idle power clocks and voltages in that Sapphire? HIS card can drop it's memory clock to 250Mz and Sapphire's minimum is 500Mz so is the -3W drop form the memory clocks? If so, 3W difference is no reason for me to change the card, but for new buyers it's good to know.

Aris
Posts: 2299
Joined: Mon Dec 15, 2003 10:29 am
Location: Bellevue, Nebraska
Contact:

Post by Aris » Wed Dec 03, 2008 2:02 pm

lechuck wrote:@Aris: You know that's not true! Do a little research before you post.
I did my research, how about you do yours.

http://archive.atomicmpc.com.au/forums. ... t=9354&p=0

HD4670 10W-70W
8800 GT 35W-78W (512MB)
8800 GT 31W-50W (256MB)

I did specify the 256mb version, not the 80w load 512mb version.

BillyBuerger
Patron of SPCR
Posts: 857
Joined: Fri Dec 27, 2002 1:49 pm
Location: Somerset, WI - USA
Contact:

Post by BillyBuerger » Wed Dec 03, 2008 5:01 pm

Aris wrote:I did my research, how about you do yours.

http://archive.atomicmpc.com.au/forums. ... t=9354&p=0

HD4670 10W-70W
8800 GT 35W-78W (512MB)
8800 GT 31W-50W (256MB)

I did specify the 256mb version, not the 80w load 512mb version.
Not to get in the middle, but these quoted values come from different sources. You can't really make any exact conclusions from this list if they weren't measured the same. SPCR's own review of the HD4670 gave a much lower load wattage of 40W than the 70W quoted in this article.

Code: Select all

HD4670 ______________#¦)######}| 10W-70W %
8800 GT _____________###¦)##| 31W-50W ^ (256MB) 

% = The official "peak power consumption" from the manufacturer 
^ = Found at www.anandtech.com

lechuck
Posts: 86
Joined: Mon Dec 04, 2006 11:57 pm
Location: EU

Post by lechuck » Thu Dec 04, 2008 6:07 am

@Aris: I guess you did some research, but your source is not reliable.
Why? Even in theory 4670 can't have 70W consumption. Remember, the card has no external power
and max. it can get from MB is 75W (on paper). No company would go so close to the limit, so about
50W is more realistic. I didn't test the card myself yet, but I read every review out there...

Xbitlabs proved to be accurate over time. You should not thrust any review 100%, there are variations
between brands too.

And as we are talking here about silent card, the idle power is very important. I overlooked 256MB, but
anyway, any card with more than 20-25W in idle is not suitable for passive.
So 8800GT -> more than 30W idle + no or very little airflow = cooking

Matija
Posts: 780
Joined: Sat Mar 17, 2007 3:17 am
Location: Croatia

Post by Matija » Sat Dec 06, 2008 4:53 am

HR-03 CANNOT BE USED WITH THIS CARD.

The mounting holes don't fit.

Edit: I have absolutely no idea what to do now. Maybe I should get some kind of a metal plate and drill properly-spaced holes in it...

Ksanderash
Posts: 353
Joined: Sat Oct 18, 2008 6:30 am
Location: Moldova, exUSSR

Post by Ksanderash » Sat Dec 06, 2008 6:16 am

At last had some time to tinker about the 4670.

Well, my Force3D doesn't go to 0.9V in idle. Instead of 0.9V I see 1.28V, and 1.34V under 3D load :(

And how much volts do you have folks on GPU?

Maybe to have full PowerPlay support through firmware we must have as much similar to reference design board as possible -- I tried two different firmwares and I can say that my card doesn't support VID shifting, and I think this is the only reason not getting 4W idle as SPCR reviewer has got.

1. IXBT's 4670 reference:
Image

2. My Force3D:
Image

Does anybody know what those technological micro switches on reference card are actually for? I also found three resistors that are missing on mine (see pics).

qpegasus
Posts: 17
Joined: Mon Dec 26, 2005 6:35 pm

Post by qpegasus » Sat Dec 06, 2008 8:33 am

I just put a Palit 4670 in my new build. I'd read it was "quieter" than other 4670's... so I thought together with the catalyst fan control I could have it near silent when not under load.

Wishful thinking that was. Even at the lowest speed setting it sounds like a vacuum.


I've read the accelero s2 is plenty... but can someone please confirm it will fit no problem?

Matija
Posts: 780
Joined: Sat Mar 17, 2007 3:17 am
Location: Croatia

Post by Matija » Sat Dec 06, 2008 9:06 am

It should fit, based on this image: http://www.arctic-cooling.com/pics/accs2_01l.jpg

There are three sets of screw holes on its base. I suppose the second one is for PCBs with mounting holes spaced 43mm apart.

I still can't figure out what to do with my HR-03... Damn it, all I want is a passively-cooled graphics card :(

Post Reply