Hyphe wrote:Great review. To bad about the HSF...
Could anybody tell me, or make a test if this motherboard, with the built in graphics, could play a WMVHD 1080p movie? I am planning to build a HTPC and I am not really sure what type of processor to buy for it to be able to cover playback of most formats. Would, for example Pentium M 745 be enough?
AOpen i915GMm-HFS: 2nd Gen Pentium M desktop board
-
- Posts: 9
- Joined: Mon Jun 27, 2005 7:39 pm
- Location: California
Re: WMVHD Test
It sure would be helpful to me if someone would answer Hyphe's questions. If the MB were to require a separate video card to drive a HD projector at 1080p resolution, the MB would not be able to my needs - heat and other issues aside. Thanks (This is a great forum)
-
- Posts: 9
- Joined: Mon Jun 27, 2005 7:39 pm
- Location: California
A lot of the newer GPUs provide WMV-HD decode assistance which takes some of the load off the CPU. In fact, I'd say that if you're talking about 1080p, such support would be almost necessary as the amount of processing to be done could be too much for all but the fastest CPU to cope with.
I've no experience of using the integrated graphics in the 915 but I'd be surprised if it provided any assistance to WMV-HD decode.
I've no experience of using the integrated graphics in the 915 but I'd be surprised if it provided any assistance to WMV-HD decode.
The integrated graphics does not seem to be that impressive so I think I'll have to get a seperate GPU anyway...
Did you recieve the heatsinks from Aopen? Will it be updated soon?MikeC wrote:Anyway, since the review was posted, I've been contacted by AOpen about a new, improved HSF for this board, which is being sent to both RH and myself -- RH will test its efficacy and I will measure / record the noise.
-
- SPCR Reviewer
- Posts: 8636
- Joined: Sat Nov 23, 2002 6:33 am
- Location: Sunny SoCal
I got mine, and will test it when I have the time and inclination.Hyphe wrote:The integrated graphics does not seem to be that impressive so I think I'll have to get a seperate GPU anyway...
Did you recieve the heatsinks from Aopen? Will it be updated soon?MikeC wrote:Anyway, since the review was posted, I've been contacted by AOpen about a new, improved HSF for this board, which is being sent to both RH and myself -- RH will test its efficacy and I will measure / record the noise.
I spent a lot of time (actually, "wasted a lot of time" might be more appropriate) working with the stupid original heatsink, and when I was done with the review I tore down the 915 setup and rebuilt my earlier 855GMe setup. At this point, I am not too inclined to rip it apart again, just to test this latest attempt. I'll do it, but don't hold your breath.
Hehe ok, I understand...
I got some answers to the question I had earlier, take a look at this thread on avs:
http://www.avsforum.com/avs-vb/showthread.php?t=555685
I got some answers to the question I had earlier, take a look at this thread on avs:
http://www.avsforum.com/avs-vb/showthread.php?t=555685
-
- SPCR Reviewer
- Posts: 8636
- Joined: Sat Nov 23, 2002 6:33 am
- Location: Sunny SoCal
Looks like all they're selling is an adapter that lets you mount an Alpha PAL6035 on that board.Since I can't read Japanese, I can't tell if they're selling the four year old Alpha along with the adapter.dragonii wrote:Look for the our motherboard name and you'll find the one that apparently matches. Now, if only I could order it...
Passive cooling for the pentium-m
Here's a great alternative to you guys who bought this motherboard but can't find a good cooling solution. It's made for their own case but could fit other cases/cooling solutions.
A passive heatpipe solution adapted for the 479 socket, they even have a picture showing it mounted on a i915Gmm-HFS...
http://www.t-balancer.com/catalog/produ ... 677a0ce595
A passive heatpipe solution adapted for the 479 socket, they even have a picture showing it mounted on a i915Gmm-HFS...
http://www.t-balancer.com/catalog/produ ... 677a0ce595
Thanks for the lin. Seems promising (no fan).
Who's willing to take the plunge and try out one ? I was looking into the Zalman Cu range as mentionned in the article as a desperate measure but I'm unsure if the Zalman will fit into my HTPC case (have the 5.25 bay a few cm above the CPU). Well, I'll probably order one of these and see how it goes...
Who's willing to take the plunge and try out one ? I was looking into the Zalman Cu range as mentionned in the article as a desperate measure but I'm unsure if the Zalman will fit into my HTPC case (have the 5.25 bay a few cm above the CPU). Well, I'll probably order one of these and see how it goes...
Regarding the cpu cooling I sort it out in this way:
http://forums.silentpcreview.com/viewtopic.php?t=23742
Now I hope Microcool made a NorthPole with a new clip
http://forums.silentpcreview.com/viewtopic.php?t=23742
Now I hope Microcool made a NorthPole with a new clip
Mr. Hutter,
first of all I would like to thank you now for your great review. I really appreciate your profound approach. I have tried to reach similar results as you by undervolting my 760 CPU to 1.1V. But even that didn't prevent my CPU from idling at a temp of 60C and more. Under max load the temperature now seems to be stable at 70-75C with fan running at 100%. Maybe I need to reinstall the heatsink. BTW, where did you place those rubber shims, below the board or on top between board and heatsink? I have them on top but they do not seem to serve for anything.
Unfortunately I found out that undervolting my system seems to lead to a loss of stability. Running Prime95 Torture Test failed after a short period of time (<1 min.). Now having set to voltage back to its default value of 1.308V the torture test runs fine (since several ours by now without an error). Maybe this is also caused by my ultra-low-latency memory (2 GB GEIL 533MHz, 3-3-3-8), but I am not sure.
As many others I am still looking for an alternative cooler solution. The ones recently posted by chiccoweb and Hyphe are looking promisingly, particulary the passive one. Now I am looking forward to any testing results.
Thanks to all who are testing and trying out things are share their experiences...
first of all I would like to thank you now for your great review. I really appreciate your profound approach. I have tried to reach similar results as you by undervolting my 760 CPU to 1.1V. But even that didn't prevent my CPU from idling at a temp of 60C and more. Under max load the temperature now seems to be stable at 70-75C with fan running at 100%. Maybe I need to reinstall the heatsink. BTW, where did you place those rubber shims, below the board or on top between board and heatsink? I have them on top but they do not seem to serve for anything.
Unfortunately I found out that undervolting my system seems to lead to a loss of stability. Running Prime95 Torture Test failed after a short period of time (<1 min.). Now having set to voltage back to its default value of 1.308V the torture test runs fine (since several ours by now without an error). Maybe this is also caused by my ultra-low-latency memory (2 GB GEIL 533MHz, 3-3-3-8), but I am not sure.
As many others I am still looking for an alternative cooler solution. The ones recently posted by chiccoweb and Hyphe are looking promisingly, particulary the passive one. Now I am looking forward to any testing results.
Thanks to all who are testing and trying out things are share their experiences...
-
- SPCR Reviewer
- Posts: 8636
- Joined: Sat Nov 23, 2002 6:33 am
- Location: Sunny SoCal
I placed them between the top of the stiffening bracket and the underside of the mobo. I also tried leaving them out altogether, hoping for better contact between the HS and the CPU die, but that made no difference in my temps.fucoboy wrote: BTW, where did you place those rubber shims, below the board or on top between board and heatsink? I have them on top but they do not seem to serve for anything.
Undervolting too much can lead to the exact same type of instability as if you were overclocking too much without enough Vcore. It's just as important to check the stability of an undervolted system as it is to check an OC'ed system.fucoboy wrote:Unfortunately I found out that undervolting my system seems to lead to a loss of stability. Running Prime95 Torture Test failed after a short period of time (<1 min.).
Every CPU is different, and just because mine will run stable at 1.1V doesn't mean yours will. I suggest you try again. but start out at 1.15V or something. If that errors out in Prime95, raise it to 1.175 and try again. Eventually you'll find a stable setting and will be able to run it there.
Just to confirm Ralf--I have a half dozen P-M's, and all will undervolt stably in the 1.1-1.2 range, but not all will do 1.1.Ralf Hutter wrote:Undervolting too much can lead to the exact same type of instability as if you were overclocking too much without enough Vcore. It's just as important to check the stability of an undervolted system as it is to check an OC'ed system.fucoboy wrote:Unfortunately I found out that undervolting my system seems to lead to a loss of stability. Running Prime95 Torture Test failed after a short period of time (<1 min.).
Every CPU is different, and just because mine will run stable at 1.1V doesn't mean yours will. I suggest you try again. but start out at 1.15V or something. If that errors out in Prime95, raise it to 1.175 and try again. Eventually you'll find a stable setting and will be able to run it there.
-
- Friend of SPCR
- Posts: 454
- Joined: Tue Aug 02, 2005 3:32 am
- Location: SF Bay Area, California
First of all, great review, Ralf!
I have a couple questions. What's up with the i915Ga-HFS? Basically, it's an ATX version of the board? If so, does the HSF still mount non-standardly?
Secondly, would anyone be willing to mod a heatsink for me that would work well on this board? I've heard good things about modding pretty basic heatsinks, so perhaps a mid-high end one would be the one for me. I'd obviously pay you for your work and I hear it takes under an hour. I'm just a little concerned about trying to do that myself and do not even have the proper tools to drill through thick copper, for example.
Oh, and finallly - would a 7800GTX fit in here? Obviously, it's a little cramped and whatnot.
Anyway, if you're willing to help me by modding a heatsink, please reply. Thank you!
I have a couple questions. What's up with the i915Ga-HFS? Basically, it's an ATX version of the board? If so, does the HSF still mount non-standardly?
Secondly, would anyone be willing to mod a heatsink for me that would work well on this board? I've heard good things about modding pretty basic heatsinks, so perhaps a mid-high end one would be the one for me. I'd obviously pay you for your work and I hear it takes under an hour. I'm just a little concerned about trying to do that myself and do not even have the proper tools to drill through thick copper, for example.
Oh, and finallly - would a 7800GTX fit in here? Obviously, it's a little cramped and whatnot.
Anyway, if you're willing to help me by modding a heatsink, please reply. Thank you!
Still seems hot
61 degrees still seems really hot for the cpu under load. Not sure they made that much of an improvement. I'd rather see them redesign the mounting bracket to use after market copper heat sinks. This board was really intriguing, but a pentium-m chip & board is too expensive to run hotter than an athlon 64 venice combo with a decent heat sink. Just my 2 cents.
Re: Still seems hot
I wonder if this is the sensor. I mounted a modified Thermaltake Volcano 10 (all copper) with an 80mm panaflow (medium airflow version) at 12v, blowing through a 80mm-60mm adapter, and I STILL get 55-57C temps when running Prime95. It's been anywhere between 25-35C in my house over the past few weeks, fwiw.mc2wheels wrote:61 degrees still seems really hot for the cpu under load. Not sure they made that much of an improvement. I'd rather see them redesign the mounting bracket to use after market copper heat sinks. This board was really intriguing, but a pentium-m chip & board is too expensive to run hotter than an athlon 64 venice combo with a decent heat sink. Just my 2 cents.
-j
-
- Posts: 37
- Joined: Fri May 13, 2005 8:33 am
This board is still at least 100 dollars too expensive, even with dual gigabit LAN and DDR2 RAM (both of which I don't need). Combined with the also-pricey Pentium M, this setup gets an extreme beatdown when it comes to the price/quiet performance ratio of a C&Q AMD64 w/ mATX board (lacking only gigabit LAN and DDR2).
-
- SPCR Reviewer
- Posts: 8636
- Joined: Sat Nov 23, 2002 6:33 am
- Location: Sunny SoCal
Re: Still seems hot
Sigh....joemadeus wrote:I wonder if this is the sensor.mc2wheels wrote:61 degrees still seems really hot for the cpu under load. Not sure they made that much of an improvement. I'd rather see them redesign the mounting bracket to use after market copper heat sinks. This board was really intriguing, but a pentium-m chip & board is too expensive to run hotter than an athlon 64 venice combo with a decent heat sink. Just my 2 cents.
As I've noted over and over, the sensor is as accurate as the one on the AOpen 855 board.
I mounted a Zalman 7000 (modded with a 92mm Nexus running at 5V) on the 915 board and the CPU load temps dropped right down to the low 40°C range, exactly the same as is reported by the 855 board using the same CPU and HSF combo.
And as far as this goes:
It's definitely not too hot, but if it worries you, just drop the Vcore down to 1.100V and your load temps will drop to around 50°C, if that makes you feel more comfortable (because the CPU won't care either way).mc2wheels wrote:61 degrees still seems really hot for the cpu under load.
I guess I'm just used to my AXP-M 2400+ @1.1v/1.2Ghz with my zalman 7000 with fan running @5v that stays in the high 30's. When I run it overclocked @1.35v/2.0Ghz with the zalman running @7v it runs in the high 40s to 50 range (depending on ambient). Again, I just think it's really a bad design flaw to not allow aftermarket coolers. 61 may not be too hot, but it doesn't seem ideal.
Modified Zalman 7000 Mod
I bought a 915GMm MB to use in my new HTPC. I didn't like the stock HSF and read that the Zalman 7000 fit, so I got one of those also.
One problem, the 7000 (7000A in my case) interferes with the PCI-E x16 slot. I am using a Sapphire x800 with Arctic Cooling ATI5 Rev 2 cooler. I trimmed about 10 fins that were a problem, and now it looks kind of like a Zalman VF700. I can post a pic if there is interest, but it was not a big deal with a Dremel and a cut-off wheel.
I overclocked the 735 to 2261 MHz (17 x 133), and 1.2V. I fold constantly, so no idle temp, but 49-50C under load. This is in a horribly poor flowing case, so I am very happy. Considering I found the 7000A for $17, it is almost perfect.
So noone else makes the mistake i did, it looks like a VF700 VGA cooler sould fit, but it sits way to close to the motherboard, and interferes with lots of stuff.
One problem, the 7000 (7000A in my case) interferes with the PCI-E x16 slot. I am using a Sapphire x800 with Arctic Cooling ATI5 Rev 2 cooler. I trimmed about 10 fins that were a problem, and now it looks kind of like a Zalman VF700. I can post a pic if there is interest, but it was not a big deal with a Dremel and a cut-off wheel.
I overclocked the 735 to 2261 MHz (17 x 133), and 1.2V. I fold constantly, so no idle temp, but 49-50C under load. This is in a horribly poor flowing case, so I am very happy. Considering I found the 7000A for $17, it is almost perfect.
So noone else makes the mistake i did, it looks like a VF700 VGA cooler sould fit, but it sits way to close to the motherboard, and interferes with lots of stuff.