Super bright case leds
Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Lawrence Lee
-
- Posts: 3142
- Joined: Mon Feb 26, 2007 9:20 am
- Location: Missing in Finnish wilderness, howling to moon with wolf brethren and walking with brother bears
- Contact:
Super bright case leds
If there is something I hate those are super bright power and HDD led's. Antec P18x and Antec Nine Hundred are wonderful cases for their purpouses. Only draw back is that during night timne, their leds blind you. P182's power and HDD leds and Antec Nine hundreds HDD led can really blind guy in a dark. I really hate that. Super bright blue leds in dark is the worse combination you can have IMHO.
One solution is not to plug the cords and mobo but when you got really quiet, almost inaudiable computer the led is usually only way to check if computer is on, if monitor is shut down like I usually do when I go sleep.
I've found some solution that works for myself though. I use some drop of glass paint over the led and once it dries in an hour, the light will be dimmed heavily and its shade is changed ( depending on colour used ) I found out that emerald green dimmens and softens the light quite considerable way, if led is blue. Enough for not being visible unless looked directly, unlike regular antec's blue leds that brighten entire room...
I really hope Antec would use less bright leds and personally... more softer colours like amberish or orangish light with warm green.
One solution is not to plug the cords and mobo but when you got really quiet, almost inaudiable computer the led is usually only way to check if computer is on, if monitor is shut down like I usually do when I go sleep.
I've found some solution that works for myself though. I use some drop of glass paint over the led and once it dries in an hour, the light will be dimmed heavily and its shade is changed ( depending on colour used ) I found out that emerald green dimmens and softens the light quite considerable way, if led is blue. Enough for not being visible unless looked directly, unlike regular antec's blue leds that brighten entire room...
I really hope Antec would use less bright leds and personally... more softer colours like amberish or orangish light with warm green.
-
- Friend of SPCR
- Posts: 356
- Joined: Wed Jan 16, 2008 8:56 pm
- Location: Council Bluffs, Iowa
- Contact:
This is one of my least favorite trends in computing, and even the big system integrators like Dell and HP are guilty. For crying out loud, people - they're indicators, not flashlights.
I replaced the blue flashlights in my SOLO with green and yellow LEDs of more reasonable brightness. Due to the complicated way the motherboard supplies power to the lights, there's no need to install a resistor in series or anything like that. Just pull the old LED out and solder a new one in (make sure the orientation is the same) and you're golden.
I replaced the blue flashlights in my SOLO with green and yellow LEDs of more reasonable brightness. Due to the complicated way the motherboard supplies power to the lights, there's no need to install a resistor in series or anything like that. Just pull the old LED out and solder a new one in (make sure the orientation is the same) and you're golden.
agreed !!!!!!!!!!
Was wondering again last night why they had the lights so bright... Maybe if you get lost somewhere in your house, it's supposed to help the search and rescue team figure out where you are... maybe not... Or if there is a power outage in your house... oh wait, power outage = no power=no LED...
Maybe that's why they make computers so loud !!!! So you don't have to look at the LEDs in the first place...
Conclusion : Bright LEDs are useless !!! Who wants to put sunglasses on when you need to look at the LEDs !!
Now that I know you can change them directly on a SOLO, I'm going to change them tonight, depending on what I have in stock... Maybe Red for power and green for HD...
Was wondering again last night why they had the lights so bright... Maybe if you get lost somewhere in your house, it's supposed to help the search and rescue team figure out where you are... maybe not... Or if there is a power outage in your house... oh wait, power outage = no power=no LED...
Maybe that's why they make computers so loud !!!! So you don't have to look at the LEDs in the first place...
Conclusion : Bright LEDs are useless !!! Who wants to put sunglasses on when you need to look at the LEDs !!
Now that I know you can change them directly on a SOLO, I'm going to change them tonight, depending on what I have in stock... Maybe Red for power and green for HD...
-
- Friend of SPCR
- Posts: 356
- Joined: Wed Jan 16, 2008 8:56 pm
- Location: Council Bluffs, Iowa
- Contact:
Blue LEDs bleach paper too!
Yeah, I'm resurrecting an old thread, but I've got something interesting for people to try if they haven't already dimmed/swapped their LEDs.
I was working on a server rack that had a rackmounted KVM switch that had a terrible blue LED. It's brighter than the ones on the recent Antec cases I've used (NSK4480, NSK3480, Take4). Since it was brand new and everything, I wasn't about to crack it open. I just put a few post-it notes over the LED (~4-5 yellow ones). I also did this on my NSK3480 at home.
Well, after about six-months, I accidently knocked off the Post-It note and I noticed little white specs on the paper. Apparently, the LED bleached some of the color off the yellow paper. It was kinda interesting because you could see several spots (since the Post-It fell off and got moved periodically), and it was pretty obvious that the bottom Post-It had the biggest white/clear spots.
I've since replaced the old Post-Its with 8 blue colored Post-Its. They work much better at dimming the blue light and hopefully are more resistant to the bleaching since they should reflect the blue light (not sure about the UV component though). That was a few months ago, so I'll probably give it a few more months before taking it off and checking for bleached spots
I was working on a server rack that had a rackmounted KVM switch that had a terrible blue LED. It's brighter than the ones on the recent Antec cases I've used (NSK4480, NSK3480, Take4). Since it was brand new and everything, I wasn't about to crack it open. I just put a few post-it notes over the LED (~4-5 yellow ones). I also did this on my NSK3480 at home.
Well, after about six-months, I accidently knocked off the Post-It note and I noticed little white specs on the paper. Apparently, the LED bleached some of the color off the yellow paper. It was kinda interesting because you could see several spots (since the Post-It fell off and got moved periodically), and it was pretty obvious that the bottom Post-It had the biggest white/clear spots.
I've since replaced the old Post-Its with 8 blue colored Post-Its. They work much better at dimming the blue light and hopefully are more resistant to the bleaching since they should reflect the blue light (not sure about the UV component though). That was a few months ago, so I'll probably give it a few more months before taking it off and checking for bleached spots
I like using a post-it because it's a simple nonpermanent change, but it takes a crazy number of layers of paper to block the light.
Instead, I simply turn the sticky part of the post-it into an aluminum foil "band-aid". Cut the post-it so it's a rectangular strip. In the center, stick a small square of aluminum foil. Then apply this "band-aid" to the offending LED. It completely blocks the light.
If you want, you can poke a pinprick in the aluminum foil to leave a small dot of light.
Instead, I simply turn the sticky part of the post-it into an aluminum foil "band-aid". Cut the post-it so it's a rectangular strip. In the center, stick a small square of aluminum foil. Then apply this "band-aid" to the offending LED. It completely blocks the light.
If you want, you can poke a pinprick in the aluminum foil to leave a small dot of light.
-
- Friend of SPCR
- Posts: 356
- Joined: Wed Jan 16, 2008 8:56 pm
- Location: Council Bluffs, Iowa
- Contact:
Re: Blue LEDs bleach paper too!
There's no UV component to an LED; they emit pretty much pure spectrum light. You should be just fine in that regard.stromgald wrote:[post-its](not sure about the UV component though)....
Post-Its are a great way of dealing with the issue when you can't actually modify the lights for whatever reason. When I have friends complain about the brightness of their LEDs, it's generally not worth my time to do any soldering. Instead I create a band-aid out of clear tape and white printer paper, and stick it between the LED and the light-pipe leading to the front of the case. This works remarkably well, and only takes a few seconds. Additionally, because it's behind the front panel, it's secure and long-term, but still very easy to remove.
Since most of my stuff is black, I use a gob of black silicon rubber over the offending LED. It's easy enough to peel off when the time comes.
This reminds me how much I love my NEC LCD, it has an option for LED brightness from 0-100% in 5% increments, and also the color between blue and green. Unfortunately, the amber standby diode isn't adjustable.
I need to find a temporary way to dim, but not block, the LEDs on all my network hardware. I suppose I could just use a thin layer of the silicon.
This reminds me how much I love my NEC LCD, it has an option for LED brightness from 0-100% in 5% increments, and also the color between blue and green. Unfortunately, the amber standby diode isn't adjustable.
I need to find a temporary way to dim, but not block, the LEDs on all my network hardware. I suppose I could just use a thin layer of the silicon.
This annoying trend isn't just limited to PC's, my phone has an annoying LED which doesn't even do anything. With PC's it's half bad, since most people don't unconsciously leave them on overnight.
That was by far not the only case of excessive time-of-day-inappropriate light causing me problems. For example, my windows leaked in too much light, I had to block that. And room lighting is often excessive.
On the whole, I don't mind LED's at all, they're much more often a solution rather than a problem for me, I use them instead fluorescent lights whenever possible to deal with the aforementioned room lighting problem.
Damn mental pollutants.
That was by far not the only case of excessive time-of-day-inappropriate light causing me problems. For example, my windows leaked in too much light, I had to block that. And room lighting is often excessive.
On the whole, I don't mind LED's at all, they're much more often a solution rather than a problem for me, I use them instead fluorescent lights whenever possible to deal with the aforementioned room lighting problem.
Damn mental pollutants.