Search found 38 matches
- Wed Sep 23, 2009 3:23 pm
- Forum: System Advice / Troubleshooting
- Topic: New hardware - System halts/freeze at random - Wall of text!
- Replies: 23
- Views: 8676
I just bought one 2GB stick of RAM (KVR1333D3N9/2G) to test with, i tried with the same settings, 1333Mhz 9-9-9-24 with the same result as the Corsair memory =( I have now tried a different memory, HDD, disconnect the DVD and now i really don't know what to do. I tried the 10-10-10-25 + upping the V...
- Sun Sep 20, 2009 9:29 am
- Forum: System Advice / Troubleshooting
- Topic: New hardware - System halts/freeze at random - Wall of text!
- Replies: 23
- Views: 8676
Hi! I'm back again after a been away for a while. I have now lowered the speed of my memory to 800Mhz. I turned the memory clock down to x4.00 and the system is much more stable, i did not alter any of the timings. I ran Prime95 (with the same settings as before) and ran error free for 4 hours befor...
- Fri Sep 11, 2009 1:23 pm
- Forum: System Advice / Troubleshooting
- Topic: New hardware - System halts/freeze at random - Wall of text!
- Replies: 23
- Views: 8676
Hi again!! Now i have been running Prime95, well trying to run would be more accurate =) I ran the torture test with the deffault settings (do i need to change anything maybe?) and heres the result 1 run - System halt in test 3 2 run - System halt in test 1 3 run - System halt in test 4 4 run - Syst...
- Thu Sep 10, 2009 10:06 pm
- Forum: System Advice / Troubleshooting
- Topic: New hardware - System halts/freeze at random - Wall of text!
- Replies: 23
- Views: 8676
May I was a bit unclear I sure will test to loosen the timings of my RAM to what you suggested! It just that i haven't had the time to do it yet since this testing takes a lot of time. Sometimes my system can run clean for 4-8 hours before a system halt and when it happends i'll have to reset the ch...
- Thu Sep 10, 2009 1:35 pm
- Forum: System Advice / Troubleshooting
- Topic: New hardware - System halts/freeze at random - Wall of text!
- Replies: 23
- Views: 8676
I went to asktheramguy, Corsair tech support and asked them to check my settings for the RAM which were fine. He also recommended to up the volt for the RAM so i tried the suggested number but the random halts are still present. Btw i have gotten help decipher the minidumps from the BSOD and those a...
- Tue Sep 08, 2009 12:26 pm
- Forum: System Advice / Troubleshooting
- Topic: New hardware - System halts/freeze at random - Wall of text!
- Replies: 23
- Views: 8676
Now i have been running Memtest86+ for 25h without any errors and i disabled the Cool n' quiet function to see of that was the troublemaker, but i still get the random halts. I ran Ubuntu from a CD for 3-4 hours wihtout any problems, will have to try that for a longer period. Tomorrow i will run the...
- Sun Sep 06, 2009 6:18 am
- Forum: System Advice / Troubleshooting
- Topic: New hardware - System halts/freeze at random - Wall of text!
- Replies: 23
- Views: 8676
Hi all and thanks for youre replies, have been away for the weekend but now i'm back for some more trial and error. This can now be added to the Tried so far list. - Bank 1 and 3 - Single channel mode with Ganged mode - Tested the RAM sticks on by one in singel channel mode and in both ganged/ungang...
- Fri Sep 04, 2009 3:31 am
- Forum: System Advice / Troubleshooting
- Topic: New hardware - System halts/freeze at random - Wall of text!
- Replies: 23
- Views: 8676
New hardware - System halts/freeze at random - Wall of text!
Hi all! ## General description ## I just bought some new hardware and it is giving me a problem that i don't know what to do with. After the assembly and installation of a OS the computer hangs/freezez from time to time. I haven't found a single action that is causing this it is totally random, i co...
- Sat Aug 09, 2008 2:15 pm
- Forum: System Advice / Troubleshooting
- Topic: Comment on my new build
- Replies: 3
- Views: 1865
- Thu Aug 07, 2008 7:39 am
- Forum: System Advice / Troubleshooting
- Topic: Comment on my new build
- Replies: 3
- Views: 1865
Comment on my new build
Hi people! I'm getting close to finalizing my new build. This computer will mostly be used for gaming and general tasks like surfing etc. While performance is important i would also like to make this system reasonably quiet. I have been out of the loop for to long and hoping that you could give me s...
- Mon Nov 20, 2006 1:30 pm
- Forum: Video Cards & Monitors
- Topic: What is considered cool and hot temps for a GF 7600GS..
- Replies: 4
- Views: 2701
- Mon Nov 13, 2006 1:23 pm
- Forum: Video Cards & Monitors
- Topic: What is considered cool and hot temps for a GF 7600GS..
- Replies: 4
- Views: 2701
What is considered cool and hot temps for a GF 7600GS..
Hi all.. I just bought a GF 7600GS that are passively cooled from Gigabyte and was just wondering what is concidered hot and cool operating temps for a card like this... When i have played WoW for 1-2 hours with max on all graphics settings it reads ~75 degrees C...Is that an accepteable temp or is ...
- Thu Oct 28, 2004 5:46 pm
- Forum: The Silent Front
- Topic: Questions regarding DFI Lanparty UT NF3 250Gb and CPU tmps
- Replies: 8
- Views: 3506
- Thu Oct 28, 2004 5:31 pm
- Forum: The Silent Front
- Topic: Questions regarding DFI Lanparty UT NF3 250Gb and CPU tmps
- Replies: 8
- Views: 3506
- Thu Oct 28, 2004 4:43 pm
- Forum: The Silent Front
- Topic: Questions regarding DFI Lanparty UT NF3 250Gb and CPU tmps
- Replies: 8
- Views: 3506
The HD was brand new from dealer..Can't understand why i can't install it?? I just thought that i've read somewhere that the NF3 chipset was called NB :oops: gonna have to look that up.. I know that they are working on the temp readings when i first installed the Smartg whit shippping BIOS all temps...
- Thu Oct 28, 2004 4:10 pm
- Forum: The Silent Front
- Topic: Questions regarding DFI Lanparty UT NF3 250Gb and CPU tmps
- Replies: 8
- Views: 3506
Questions regarding DFI Lanparty UT NF3 250Gb and CPU tmps
Got a couple of questions for you people with this mobo, i think Edward NG have the same mobo as i have.. First, when i'm about to install Nvidia Forceware Network Access Mngr, after installing the chipset drivers about half way through the install i get this error message: Error 1609. An error occu...
- Thu Oct 28, 2004 5:02 am
- Forum: Video Cards & Monitors
- Topic: DFI Lanparty UT NF3 250GB and aftermarket NB HS
- Replies: 10
- Views: 4973
I don't know how other NF3 boards handle the NB heat but this DFI board gets HOT..I haven't done any OC everything is running at stock speed and after 1 hour of just surfing, playing mp3's etc, just everyday stuff, the NB HS is so hot i can't keep my finger on for more than a few seconds.. I can't u...
- Wed Oct 27, 2004 5:43 pm
- Forum: Video Cards & Monitors
- Topic: DFI Lanparty UT NF3 250GB and aftermarket NB HS
- Replies: 10
- Views: 4973
- Wed Oct 27, 2004 8:43 am
- Forum: Video Cards & Monitors
- Topic: DFI Lanparty UT NF3 250GB and aftermarket NB HS
- Replies: 10
- Views: 4973
Ok, sounds good..I think i'll go with that HS since it has a really low price and from what i understand does a good job of transfering heat.. How did you cut those fin rows off, some kind of metalsaw? If it's possible could you post a pic how it looks? I don't have a video card that big right now b...
- Tue Oct 26, 2004 3:57 pm
- Forum: Video Cards & Monitors
- Topic: DFI Lanparty UT NF3 250GB and aftermarket NB HS
- Replies: 10
- Views: 4973
DFI Lanparty UT NF3 250GB and aftermarket NB HS
Hi My HS on the NB i running so hot you can't barely touch it so i'm gonna change it to some aftermarket HS..Any good suggestions? I would like it to be fanless and if possible still have room for bigger videocard like the 6800 etc..I've been looking at the ZM-NB47J, don't know if that will clear an...
- Tue Oct 19, 2004 5:21 am
- Forum: Fans and Control
- Topic: How about the PAPST 3413NGL in terms of cooling and noise?
- Replies: 1
- Views: 1494
How about the PAPST 3413NGL in terms of cooling and noise?
Hi everybody. I'm waiting for my XP-90 cooling for my A64 3200+ and the fan that i ordered to use with it is out f stock and will be for quite some time and i am now considering a PAPST 3412NGL. Can somebody with more experience than me on the fan subject tell me if this is a good fan in terms of co...
- Wed Sep 29, 2004 3:31 pm
- Forum: System Advice / Troubleshooting
- Topic: Feedback on my A64 setup
- Replies: 3
- Views: 3431
- Wed Sep 29, 2004 1:25 pm
- Forum: System Advice / Troubleshooting
- Topic: Feedback on my A64 setup
- Replies: 3
- Views: 3431
Feedback on my A64 setup
Hi people I have finally decided my new system setup the only thing i haven't really decided yet is the cooling solution for the CPU. It stands between these two: Zalman CNPS7000B-AlCu and Thermalright XP-120 with a PAPST from the recommended list My system is gonna look like this Antec SLK3700BQE D...
- Mon Sep 06, 2004 7:07 am
- Forum: System Advice / Troubleshooting
- Topic: Help on choosing mobo..
- Replies: 22
- Views: 13029
I saw that i have forgotten to list the name of the ASUS mobo i was considering :? Sry i was tired when o wrote the post. Anyway the boards i am looking at are MSI K8N Neo Platinum and Asus K8N-E Deluxe.. Straker, those problems with memory could those be solved by BIOS updates in the future or are ...
- Sat Sep 04, 2004 3:21 pm
- Forum: System Advice / Troubleshooting
- Topic: Help on choosing mobo..
- Replies: 22
- Views: 13029
Hi everybody. After doing som reading up on A64 socket 754 i have come up with this new system and would be glad for any type of comments or other recommendation. Antec SLK3700BQE Athlon 3000+ 1024 MB Kingstone value ram (I'm not gonna overclock) CNPS7000A/B-Alcu with Arctic Silver 5 NEC ND-3500A DV...
- Mon Aug 09, 2004 12:13 pm
- Forum: System Advice / Troubleshooting
- Topic: Help on choosing mobo..
- Replies: 22
- Views: 13029
Did a quick search and found a lot of interesting reading about A64..Seems to have a nice performance vs cooling..Gonna spend some time doing some reding up on the AMD mobos and so forth.. Anybody have some good pointers to a good mobo in the pricerange and with similair features as the Asus P4800C-...
- Mon Aug 09, 2004 2:38 am
- Forum: System Advice / Troubleshooting
- Topic: Help on choosing mobo..
- Replies: 22
- Views: 13029
[quote="HammerSandwich"] Do you already have the HD? If not, buy an 0812C - that 8mb buffer helps.[/quote] Yes, it currently sits in my system and is pretty new and i'm a bit short on money for now but i will add a few more disks later on, SATA 8MB cache.. I think i will go with the value line of Ki...
- Fri Aug 06, 2004 3:34 am
- Forum: System Advice / Troubleshooting
- Topic: Help on choosing mobo..
- Replies: 22
- Views: 13029
How about Kingston value RAM line? Are they any good? I've been lookin at the Crusial Ballistix since they seems to be a popular brand..I was thinking of going with 2x512 but couldn't find any dual kits..Is it safe to buy 2 singel modules and run them in dual mode or is there a high risk for incompa...
- Thu Aug 05, 2004 10:29 pm
- Forum: System Advice / Troubleshooting
- Topic: Help on choosing mobo..
- Replies: 22
- Views: 13029
Hi. Thx for answering..I will go with the Asus board and when i looked at the pricing for 2x512 RAM it was actually cheaper then going with 4x256 so i going to wait until i have the money and go with 2x512 instead.. By the way anybody know of any problem with Twinmos memory? It looks like the brand ...
- Thu Aug 05, 2004 5:32 am
- Forum: System Advice / Troubleshooting
- Topic: Help on choosing mobo..
- Replies: 22
- Views: 13029
Help on choosing mobo..
Hi everybody. I'm about to buy me a new mobo and it stands between these two: Asus P4C800-E Deluxe This board seems to have good performance and being stable. It seems to work good with most of the different memories out there and overall get good score in hardware reviws. and Aopen AX4SPE Max II Th...