S12II fan swap
Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Lawrence Lee, Devonavar
-
- *Lifetime Patron*
- Posts: 2000
- Joined: Tue May 15, 2007 1:39 am
- Location: Finland
Looking good! Neat cables and smooth work overall. I hope to get there as I upgrade a few other components.
Did you take any measurements by chance, starting voltages and the like? Would like to know if the internal feed is the same 3.8V as in the 650 Energy+(I think it was).
How's the new fan compared to the old one?
Did you take any measurements by chance, starting voltages and the like? Would like to know if the internal feed is the same 3.8V as in the 650 Energy+(I think it was).
How's the new fan compared to the old one?
-
- Friend of SPCR
- Posts: 889
- Joined: Sun Dec 05, 2004 11:34 pm
- Location: Finland -- Folding For SPCR
Morjens,
do I didn't measure the fan controller's starting voltage. I presume it's a bit above 4V, or atleast that's what the Antec EarthWatts had. If I have the time I may still play around with it and check the voltages.
The new fan is, naturally, quieter than the older one I've been using only NMB-MAT (former NMB and Panaflo merged) for a few years now, quite happy.
Off to continue assembling my HTPC in a new Silverstone LC20
do I didn't measure the fan controller's starting voltage. I presume it's a bit above 4V, or atleast that's what the Antec EarthWatts had. If I have the time I may still play around with it and check the voltages.
The new fan is, naturally, quieter than the older one I've been using only NMB-MAT (former NMB and Panaflo merged) for a few years now, quite happy.
Off to continue assembling my HTPC in a new Silverstone LC20
-
- *Lifetime Patron*
- Posts: 2000
- Joined: Tue May 15, 2007 1:39 am
- Location: Finland
-
- Friend of SPCR
- Posts: 889
- Joined: Sun Dec 05, 2004 11:34 pm
- Location: Finland -- Folding For SPCR
Saunamies, thanks and will try.
Raziell, there was another thread where the newer S12II's were discussed. The original ADDA fan had an annoying low rumbling and whining, that was the main reason why I swapped. So...
a) the quality of the noise changed for better
b) I PRESUME, as per the EarthWatts and other Seasonic PSUs, the PSU will feed voltages below 5V until the 200W power usage (see the SPCR reviews for fan controller / power relationships).
So in fact as the new fan's top speed is a bit lower than the original fan's it will most likely spin a bit slower than the original fan, even though the PSU receives a bit less cooling (because the fan swap didn't decrease cooling enough for the fan controller to increase the fan voltage noticeably). The PSU will also have a dedicated cold air intake in my HTPC case, which will help in keeping the fan voltage low.
There's also a few of PSU modding / fan swap stickies that might help you with this matter.
Ugh, I have migrene so hopefully that made sense.
Raziell, there was another thread where the newer S12II's were discussed. The original ADDA fan had an annoying low rumbling and whining, that was the main reason why I swapped. So...
a) the quality of the noise changed for better
b) I PRESUME, as per the EarthWatts and other Seasonic PSUs, the PSU will feed voltages below 5V until the 200W power usage (see the SPCR reviews for fan controller / power relationships).
So in fact as the new fan's top speed is a bit lower than the original fan's it will most likely spin a bit slower than the original fan, even though the PSU receives a bit less cooling (because the fan swap didn't decrease cooling enough for the fan controller to increase the fan voltage noticeably). The PSU will also have a dedicated cold air intake in my HTPC case, which will help in keeping the fan voltage low.
There's also a few of PSU modding / fan swap stickies that might help you with this matter.
Ugh, I have migrene so hopefully that made sense.
-
- Posts: 65
- Joined: Fri Aug 10, 2007 6:10 am
- Location: big u.k
- Contact:
...
do you know what is rpm of that fan? (I was googling and I think it is 1700rpm.)
I ask this coz I may do a fan swap in Corsair VX450 which is pretty the same like this seasonic SII except sticks, and some capacitors, as MikeC said that.
I guess mine YL D12SL-12 (1350rpm) won't be enough rpm for fan swap, right?
I ask this coz I may do a fan swap in Corsair VX450 which is pretty the same like this seasonic SII except sticks, and some capacitors, as MikeC said that.
I guess mine YL D12SL-12 (1350rpm) won't be enough rpm for fan swap, right?
-
- *Lifetime Patron*
- Posts: 2000
- Joined: Tue May 15, 2007 1:39 am
- Location: Finland
You don't want to use that YL because it's a sleeve-bearing fan, the RPM could be enough if you have a cool ambient and good airflow.
It's originally a 2050 RPM fan but it's never gone that high for me, I'd say it tries to stay in the sub-1000 territory but has gone over 1000 from time to time during prolonged gaming this summer.http://www.addausa.com/specifications/92-120.pdf wrote:120 X 120 X 25 AD1212MB-A71GL BALL 12 0.33 3.96 2050