Control: management of fans, temp/rpm monitoring via soft/hardware
Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Lawrence Lee
-
Marxx
- Posts: 18
- Joined: Tue Jul 13, 2004 12:35 am
Post
by Marxx » Tue Jul 13, 2004 12:41 am
Hello, i have an Antec Sonata case, with 2 Antec 120mm case fans. I was wondering what exactly is the vreg fan header for? Is this where the blue fan monitoring wire from the psu connects to? Also, do you recommend plugging my case fans to the motherboard headers, or to the 5v fan only connectors on the PSU? Thanks,........Marxx
-
Deheinx
- Posts: 50
- Joined: Thu Jun 10, 2004 6:17 am
Post
by Deheinx » Tue Jul 13, 2004 6:35 am
Here is a link to Intel's website for the Bonanza motherboard. All of the connectors are explained:
http://developer.intel.com/design/mothe ... bz_con.htm
Essentially the VReg (Voltage Regulator) connector is to monitor the fan speed of your PSU if it provides the proper connection for it.
-
Marxx
- Posts: 18
- Joined: Tue Jul 13, 2004 12:35 am
Post
by Marxx » Tue Jul 13, 2004 10:37 am
Thanks for the reply, My Antec 380s psu does have a fan monitoring Blue wire lead, so I guess I'll connect it to the vreg header. Thanks for the link.....Marxx
-
Ozkar
- Posts: 179
- Joined: Tue Dec 30, 2003 6:22 pm
- Location: Queens, NY
Post
by Ozkar » Thu Jul 15, 2004 3:57 pm
AFAIK, the VREG connector can be used by any fan, not just the PSU fan.
-
Ralf Hutter
- SPCR Reviewer
- Posts: 8636
- Joined: Sat Nov 23, 2002 6:33 am
- Location: Sunny SoCal
Post
by Ralf Hutter » Fri Jul 16, 2004 5:42 am
Ozkar wrote:AFAIK, the VREG connector can be used by any fan, not just the PSU fan.
That's correct.
-
Marxx
- Posts: 18
- Joined: Tue Jul 13, 2004 12:35 am
Post
by Marxx » Sat Jul 17, 2004 12:01 pm
Do you guys recommend connecting my Antec 120mm fans to the "fan only" connectors off the power supply which i think is 5v, or to the front & rear fan headers on the motherboard? Do 120mm fans draw too much power from the motherboard? Any help would be appreciated, Thanks
-
Marxx
- Posts: 18
- Joined: Tue Jul 13, 2004 12:35 am
Post
by Marxx » Sat Jul 17, 2004 12:01 pm
Do you guys recommend connecting my Antec 120mm fans to the "fan only" connectors off the power supply which i think is 5v, or to the front & rear fan headers on the motherboard? Do 120mm fans draw too much power from the motherboard? Any help would be appreciated, Thanks
-
sthayashi
- *Lifetime Patron*
- Posts: 3214
- Joined: Wed Nov 12, 2003 10:06 am
- Location: Pittsburgh, PA
Post
by sthayashi » Sat Jul 17, 2004 8:44 pm
That's what they're there for. Plug 'em in. It will make the fan run quietly. Theoretically, the PSU will increase the voltage to the Fan-Only connectors in the event that things get too hot. In practice, it takes some serious heat to get the PSU to raise the voltage significantly.