How does one dim the Antec P150 case LED's?
Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Devonavar
How does one dim the Antec P150 case LED's?
While this isnt quiet related, I know alot of you are like me and dont care for your case to light up to bright and prefer a more low profile appearance.
I have been trying to search for an answer to this question, particularly what resistor specs I should look for to dim the blue front panel leds (power mainly, and the hdd activity also) on the antec p150 case by about 70-80%. I want to still be able to see the light, just not from space. Since I dont know anything about the specs on the two led's, finding the information I need has been troublesome.
If anyone has done something like this to their p150 or anything else I would really appreciate your input on what parts to pick up to get my desired affect, thanks in advance.
Sejin
I have been trying to search for an answer to this question, particularly what resistor specs I should look for to dim the blue front panel leds (power mainly, and the hdd activity also) on the antec p150 case by about 70-80%. I want to still be able to see the light, just not from space. Since I dont know anything about the specs on the two led's, finding the information I need has been troublesome.
If anyone has done something like this to their p150 or anything else I would really appreciate your input on what parts to pick up to get my desired affect, thanks in advance.
Sejin
-
- Posts: 74
- Joined: Sat Jan 21, 2006 6:12 pm
-
- SPCR Reviewer
- Posts: 8636
- Joined: Sat Nov 23, 2002 6:33 am
- Location: Sunny SoCal
-
- Posts: 35
- Joined: Sun Sep 18, 2005 2:39 pm
I have the same question and posted it somewhere.
I got a couple answers about soldering resistors and such as well as the paper and Sharpie offerings. If I can figure out where I posted it I'll get back to you on the resistors.
I don't get the designers, this is a really annoying aspect of almost all LED installations. I guess the notion is someone wearing lead glasses or blind or on the moon might not see the LED so best to make it as bright as is possible.
They could tone it down 90% or even more and it would still be effective. Its not like we need to read by it.
I got a couple answers about soldering resistors and such as well as the paper and Sharpie offerings. If I can figure out where I posted it I'll get back to you on the resistors.
I don't get the designers, this is a really annoying aspect of almost all LED installations. I guess the notion is someone wearing lead glasses or blind or on the moon might not see the LED so best to make it as bright as is possible.
They could tone it down 90% or even more and it would still be effective. Its not like we need to read by it.
that's exactly what I was thinkinglm wrote:If it's on, it responds to keyboard/mouse and brings the monitor out of power save mode. No leds needed.Ryan wrote:I personally need the led's on (otherwise i don't know if my pc is on), but at night it's pretty annoying. So I just added a switch into the circuit.
-
- SPCR Reviewer
- Posts: 8636
- Joined: Sat Nov 23, 2002 6:33 am
- Location: Sunny SoCal
Can you point me to the forum? Didn't see a link on the OrigenAE website and would like to give that idea a try.jhhoffma wrote:You can solder some resistors in line with the LED to dim it down. If you look on the OrigenAE forums for the X11 LED, it has a pretty good description of how to do it. I think it involved some 470Ohm or 700Ohm resistors (I got mine at Radioshack). Worked quite well on my X11 Power LED.
Thanks.
That's the problem with resurrecting a dead thread, some of the info isn't valid anymore. About a month after I made that post, OrigenAE took their forums offline and redesigned their website. They don't have a forum anymore, which is lame, as their was more info there than in their entire website.
The steps are very easy if you've ever soldered before, just snip the leads, add a 470Ohm resistor in series and solder back together and it'll reduce the brightness by about 1/2.
The steps are very easy if you've ever soldered before, just snip the leads, add a 470Ohm resistor in series and solder back together and it'll reduce the brightness by about 1/2.
-
- Posts: 21
- Joined: Sun Mar 02, 2008 5:27 pm
- Location: USA
-
- Posts: 144
- Joined: Sat Aug 02, 2003 3:46 pm
- Location: Silicon Valley
ULTRA HIGH TECH SOLUTION - a sheet of paper.
No marker or soldering needed.
Just take a piece of ordinary white inkjet or laser printer plain paper or regular writing paper of almost any sort, and just slip it between the bezel and the LED. Tape it in place with the tape of your choice.
1. Open the bezel
2. tape paper over offending LED or cut paper to shape or wedge it in. Just get a sheet of paper over the LED somehow.
3. Close bezel.
4. Declare victory to the gentle blue glow of a tamed LED.
Just take a piece of ordinary white inkjet or laser printer plain paper or regular writing paper of almost any sort, and just slip it between the bezel and the LED. Tape it in place with the tape of your choice.
1. Open the bezel
2. tape paper over offending LED or cut paper to shape or wedge it in. Just get a sheet of paper over the LED somehow.
3. Close bezel.
4. Declare victory to the gentle blue glow of a tamed LED.