PSUs: The source of DC power for all components in the PC & often a big noise source.
Moderators: NeilBlanchard, Ralf Hutter, sthayashi, Lawrence Lee, Devonavar
-
nwbdan
- Posts: 28
- Joined: Tue Jan 12, 2010 2:44 pm
- Location: EU
Post
by nwbdan » Wed Jul 28, 2010 3:14 am
I want to change the fan on my crappy noisy PSU, but I'm not sure if I've chosen the appropriate fan.
The original is a Globe Fan RL4Z S1402512M
Rated current 6-13.8V, 0.30 A
Starting voltage 6V
Rated Input Power 3.60
I want to change it with a Noiseblocker NBSilent XK2 140mm
http://www.noiseblocker.de/de/documents ... _XK_de.pdf
The rated current, starting voltage and rated input power are all different between the fans (and so are the dB 25-->19.5
![Wink ;)](./images/smilies/icon_wink.gif)
)
I just wanted to make sure I can do this fan swap OK.
Thanks in advance,
nwbdan
-
lodestar
- Posts: 1683
- Joined: Fri Aug 05, 2005 3:29 am
- Location: UK
Post
by lodestar » Wed Jul 28, 2010 4:56 am
You are replacing a 1200 rpm fan with an 1100 rpm model, but I don't see that would make much difference. Current fan is likely to be 2 wire with a 2 pin header on the PSU circuit board, so you may have to modify the replacement fan connector.
-
nwbdan
- Posts: 28
- Joined: Tue Jan 12, 2010 2:44 pm
- Location: EU
Post
by nwbdan » Thu Jul 29, 2010 3:11 am
From the reviews I've read the current fan really is two pin - two pin fan header. I was tinking that you could just connect the fan header from the new fan to the fan header on the PSU, but leaving one of the "holes" with no pin. Is there any other modification I have to do?
-
lodestar
- Posts: 1683
- Joined: Fri Aug 05, 2005 3:29 am
- Location: UK
Post
by lodestar » Thu Jul 29, 2010 5:25 am
It depends on the fan header on the PSU circuit board. If it is open then it will take a three pin fan connector, and the third wire (yellow - fan rpm sensing) remains but connects to nothing. If the fan header is a socket, you may find that it will just pull off and then the 3 pin fan connector will fit. Observe the cable orientation first, if you do this. Failing this, the fan connector can be reduced to two wires by cutting off the third yellow wire part with a sharp craft knife. The yellow wire can then be removed, or trimmed back as far as possible.
-
nwbdan
- Posts: 28
- Joined: Tue Jan 12, 2010 2:44 pm
- Location: EU
Post
by nwbdan » Thu Jul 29, 2010 10:45 am
One of the (few) reviews I could find has a pic of the PSU circuit board fan header:
http://www.islabit.com/13593/ultra-revi ... lle.html/8
(spanish review, but the pics there)
Will it work?
Also, I have a very limited supply of 140mm in the shops around here, but are there any other 140mm fans you would like to suggest?
I thank you for all your help so far.
Nwbdan
-
lodestar
- Posts: 1683
- Joined: Fri Aug 05, 2005 3:29 am
- Location: UK
Post
by lodestar » Thu Jul 29, 2010 7:40 pm
It looks like the best option will be to trim the 3 pin connector to fit the 2 pin socket. Your choice of 140mm is fine, it will be quieter and it should have a rather better quality bearing.
-
nwbdan
- Posts: 28
- Joined: Tue Jan 12, 2010 2:44 pm
- Location: EU
Post
by nwbdan » Fri Jul 30, 2010 12:40 am
-
walle
- Posts: 605
- Joined: Tue Dec 26, 2006 10:52 am
Post
by walle » Fri Jul 30, 2010 1:28 am
No need to trim the 3 pin connector. simply remove the 2 pin SOCKET on the PSB board and connect the 3 pin connector like you would the 2 pin connector.
-
nwbdan
- Posts: 28
- Joined: Tue Jan 12, 2010 2:44 pm
- Location: EU
Post
by nwbdan » Fri Jul 30, 2010 5:57 am
walle wrote:No need to trim the 3 pin connector. simply remove the 2 pin SOCKET on the PSB board and connect the 3 pin connector like you would the 2 pin connector.
Just like the pictures posted above, correct?
-
walle
- Posts: 605
- Joined: Tue Dec 26, 2006 10:52 am
Post
by walle » Fri Jul 30, 2010 12:09 pm
nwbdan wrote:Just like the pictures posted above, correct?
Correct.